Epson Stylus NX430 Small-in-One

5 Load paper against the right edge guide and behind the
tab, with the printable side faceup.
8½ × 11 inch
(216 × 279 mm)
4 × 6 inch
(102 × 152 mm)
Note: Don’t load the paper sideways; always load it short
edge first.
6 Slide the edge guide over, against the left edge of
the paper.
7 Flip the feeder guard back.
Read these instructions before using your product.
1
Unpack
Caution: Do not open ink cartridge packages until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
Remove all protective materials, including from inside the printer.
2
Turn on and adjust
1 Raise the paper support, then connect the power cord.
Caution: Do not connect to your computer yet.
2 Raise the control panel, then press the power button.
To lower the control panel, squeeze the release bar
underneath and push the control panel down.
Caution: Do not lower the control panel without first squeezing the
release bar underneath or you may damage the product.
3
Select language
To select English as your language, press OK.
Note: If you want to change the language, press or to select it,
then press OK.
4
Install ink cartridges
Note: Don’t load paper yet.
1 Lift up the scanner, and wait until the ink cartridge holder
stops moving.
2 Shake the ink cartridges gently 4 or 5 times, then
unpack them.
3 Remove only the yellow tape from each cartridge.
Caution: Don’t remove any other seals or the cartridges may leak.
4 Insert the cartridges in the holder for each color, and press
each cartridge down until it clicks.
5 Lower the scanner.
6 Press OK to prime the ink delivery system. Priming takes
about 4 minutes.
Note: Your printer ships with full cartridges and part of the ink from
the first cartridges is used for priming the printer.
Caution: Don’t turn off the printer while it is priming or you’ll
waste ink.
5
Load paper
1 Flip the feeder guard forward.
2 Raise the paper support, if necessary. Then pull up the
extension and tilt it back slightly.
3 Pull out the output tray, then raise the stopper.
4 Slide the edge guide to the left.
*412086500*
*412086500*
Epson Stylus
®
NX430
Small-in-One
™
Start Here

Epson Stylus NX430 Small-in-One Specifications

General

Print Technology	Inkjet
Maximum Print Resolution	5760 x 1440 optimized dpi
Scanner Type	Color Flatbed
Scanner Resolution	1200 x 2400 dpi
Connectivity	USB, Wi-Fi
Display	2.5" LCD
Functions	Print, Copy, Scan
Ink Cartridge Configuration	4 individual ink cartridges
Input Capacity	100 sheets
Output Capacity	30 sheets
Paper Sizes	A4, A6, 4 x 6", 5 x 7", letter, legal, envelopes
Dimensions	15.4 x 11.8 x 5.7 inches
Weight	9 lbs
Memory Card Support	SD, SDHC
Ink Cartridges	Black, Cyan, Magenta, Yellow
Operating System Compatibility	Windows, Mac

Summary

Unpack and Prepare Printer

Unpack Printer and Remove Materials

Remove all protective materials from the printer and its packaging before setup.

Power On and Adjust Settings

Connect power, raise paper support, turn on printer, and adjust control panel.

Select Display Language

Choose the desired language from the printer's screen and confirm.

Install Ink Cartridges

Prepare and insert ink cartridges into the holder until they click.

Ink Priming and Paper Loading

Initiate Ink Priming

Press OK to start the ink delivery system priming process.

Load Paper Correctly

Load paper into the feeder, aligning guides and ensuring correct orientation.

Printer Connectivity and Software Installation

Configure Printer Connection

Connect the printer to your network or computer via USB.

Install Printer Software

Install the necessary drivers and software from the CD or website.

Troubleshooting and Supplies

Troubleshoot Common Setup Issues

Resolve problems like network setup failure or dark printer screens.

Order Printer Supplies

Information on purchasing genuine Epson paper and ink cartridges.

Recycling Program Information

Details on Epson's recycling program for used hardware and ink cartridges.