EasyManuals Logo

Epson TM-m30II User Manual

Epson TM-m30II
115 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #108 background imageLoading...
Page #108 background image
108
Appendix
You can connect to a WPA2-PSK (AES) access point using the settings above.
Settings in SimpleAP mode (Factory default settings)
In SimpleAP mode, DHCP Server is working and assign IP address to host automatically.
Notes on Using the Wi-Fi Model
Keep the printer away from the devices, such as kitchen microwaves, that may cause radio wave interference.
Use channels that are away from the frequency bands that may cause radio wave interference.
Place shields between the printer and the devices that may cause radio wave interference.
Select either 2.4 GHz or 5 GHz, whichever is free from radio wave interference.
In auto channel setting for the access point, do not select a channel in which the printer may cause radio
wave interference.
Notes on Wi-Fi connection
Because not all the combinations of the printer and Wireless LAN units have been checked for operation, the
operation of the printer in combination with all the Wireless LAN units is not guaranteed. Especially in the ad-
hoc mode, the printer may not operate normally, depending on the combination of the device to connect with.
Be sure to carry out evaluation of the operation before use.
Notes on use
When you initialize or change the printer settings, the printer is reset to reflect the settings. It may take about
1 minute depending on the network settings or environment. Also, your application may indicate power off
during the time waiting for reset. In that case, wait for about 1 minute, and then reconnect to the printer.
Where Wi-Fi communication is in heavy traffic, your application may falsely recognize that the
communication is disconnected and indicate power off due to response delay. In that case, disable Power
Save to improve the trouble.
Parameter Setting value
Communication standard 802.11b/g/n
Network mode Infrastructure mode
SSID EPSON_Printer
Encryption type WPA2-Personal
Passphrase EpsonNet
IP Address Automatically acquired by DHCP
Parameter Setting value
SSID EPSON_Printer
Passphrase 12345678
IP Address 192.168.192.168
Subnet mask 255.255.255.0

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson TM-m30II and is the answer not in the manual?

Epson TM-m30II Specifications

General IconGeneral
TypePOS printer
Character setsANK
Print technologyDirect thermal
Maximum resolution203 x 203 DPI
Maximum roll diameter83 mm
Supported paper width58 mm - 80 mm (Breite) mm
Maximum printing width80 mm
Power plug typeType G
Power source typeAC
USB portYes
USB connectorUSB Type-A / USB Type-B
USB 2.0 ports quantity2
Connectivity technologyWired
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)5 - 45 °C
Operating relative humidity (H-H)10 - 90 %
Wi-FiNo
Internal memory- MB
Built-in barcodes-
Country of originPhilippines
Mounting positionHorizontal/Vertical
Autocutter durability1.5 million cuts
Built-in sensors detailsPaper End Sensor, Papier-Sensor
Sound pressure level (printing)55 dB
Mean time between failures (MTBF)360000 h
Product colorWhite
Print head life150.000.000 Impulse
Mean cycles between failures (MCBF)65000000
Pre-installed softwareTMNet WebConfig, ePOS-Device, ePOS-Display, ePOS-Print
Package depth240 mm
Package width200 mm
Package weight2150 g
Quantity per pack1 pc(s)
Quantity per pallet128 pc(s)
Quantity per pallet (UK)192 pc(s)
Master (outer) case width400 mm
Master (outer) case height255 mm
Master (outer) case length490 mm
Master (outer) case weight0 g
Harmonized System (HS) code84433210
Quantity per master (outer) case4 pc(s)
Weight and Dimensions IconWeight and Dimensions
Width127 mm

Related product manuals