EQUATION A007H-05C User Manual (English)

Questions and Answers:

C
Connie WilliamsAug 5, 2025
What to do if my EQUATION A007H-05C is not cool enough?
- F
  Francisco HarrisonAug 5, 2025
  If your EQUATION Air Conditioner isn't cooling sufficiently, several factors could be the cause. First, ensure that all doors and windows are completely closed. Check for any heat sources in the room and remove them if possible. Make sure the exhaust air hose is properly connected and not blocked; clean it if necessary. Also, verify that the temperature setting isn't too high and reset it to a cooler setting. Finally, inspect the air inlet to ensure it's clean and not blocked.
A
Angelica MooreAug 9, 2025
What to do if my EQUATION A007H-05C does not start?
- J
  Jeremy SmithAug 9, 2025
  If your EQUATION Air Conditioner fails to start when you press the on/off button, there are a few potential reasons: * The water tank might be full, and the water full indicator lamp is blinking. If so, empty the water tank. * If you are using electric heating mode, the room temperature may be higher than the set temperature. In that case, reset the temperature. * If you are using cooling mode, the room temperature may be lower than the set temperature. Try resetting the temperature.
J
Jessica CollinsAug 15, 2025
Why is my EQUATION A007H-05C Air Conditioner so noisy?
- T
  Thomas HuntAug 15, 2025
  The noise from your EQUATION Air Conditioner could stem from a couple of reasons. If the unit is placed on ground that isn't level or flat, try moving it to a flat, level surface. Alternatively, the sound might be due to the normal flowing of refrigerant inside the air conditioner, which is not a cause for concern.
D
Deborah FriedmanAug 19, 2025
What does E2 code mean on my EQUATION Air Conditioner and how to fix it?
- R
  rgrayAug 19, 2025
  The E2 code on your EQUATION Air Conditioner indicates that the water tank is full during cooling. To resolve this, take off the rubber stopper and empty the water from the tank.
B
Bailey MillerAug 26, 2025
What does E0 code mean on my EQUATION A007H-05C?
- A
  aliciastarkAug 26, 2025
  The E0 code on your EQUATION Air Conditioner indicates that the room temperature sensor has failed. You can replace the room temperature sensor, but the unit can still function without replacing it.
V
vfrankAug 29, 2025
What does E1 code mean on my EQUATION Air Conditioner?
- J
  josephseanAug 29, 2025
  The E1 code on your EQUATION Air Conditioner means that the condenser temperature sensor has failed. Replace the condenser temperature sensor to resolve this issue.

EQUATION A007H-05C Specifications

General

Brand	EQUATION
Model	A007H-05C
Category	Air Conditioner
Language	English

Summary

Safety Precautions

Warning Symbols

Illustrates and explains key safety symbols for proper appliance usage and potential hazards.

General Safety Principles

Outlines fundamental guidelines for safe operation and maintenance, emphasizing user responsibility.

General Safety Rules

Provides specific instructions to prevent accidents, such as avoiding obstructions and filter usage.

Appliance Specifications

Installation, Assembly, and Parts Identification

Front Side Components

Identifies key components located on the front of the air conditioner, including the control panel and venting frame.

Back Side Components

Lists and identifies essential parts on the rear of the unit, such as the handle, dust screen, and drain plug.

Operation Methods

Control Panel Appearance and Function

Details the layout and functions of the air conditioner's control panel, including buttons and indicators.

Before Using the Appliance

Operation Temperature Range

Specifies the recommended operating temperature range for cooling and dehumidifying functions.

Cooling and Dehumidifying Cautions

Provides important interval and operational notes for cooling and dehumidifying modes to prevent damage.

Power Supply Requirements

Details the necessary power supply specifications, including socket type and usage restrictions.

Installation Explanation

Introduction to Exhaust Hose Installation

Installation and Maintenance

Temporary and Window Slider Installation

Guides for temporary installation and fitting the window slider kit for exhaust hose setup.

Water Full Alarm Function

Explains the water full indicator light and how to handle a full water tank, including pump damage scenarios.

Maintenance Procedures

Outlines essential maintenance steps, including cleaning precautions and contacting service for repairs.

Maintenance

Air Filter Cleaning

Instructions for dismounting, cleaning, and remounting the air filter to maintain unit performance.

Air-Conditioner Surface Cleaning

Details on how to safely clean the exterior surface of the air conditioner using mild detergents.

Troubleshooting

Unit Not Starting

Addresses issues where the unit fails to start after pressing the power button, listing causes and solutions.

Insufficient Cooling

Covers scenarios where the unit does not cool effectively, identifying common causes and remedies.

Noisy Operation

Explains potential causes of noise during operation, including refrigerant sounds and improper leveling.

Error Codes (E0, E1, E2)

Details specific error codes related to sensor failures or water tank status, providing replacement guidance.

Related product manuals

EQUATION OL-BKY26-A010B2

EQUATION A007H-05C User Manual

Table of Contents

Questions and Answers:

EQUATION A007H-05C Specifications

Summary

Safety Precautions

Warning Symbols

General Safety Principles

General Safety Rules

Appliance Specifications

Installation, Assembly, and Parts Identification

Front Side Components

Back Side Components

Operation Methods

Control Panel Appearance and Function

Before Using the Appliance

Operation Temperature Range

Cooling and Dehumidifying Cautions

Power Supply Requirements

Installation Explanation

Introduction to Exhaust Hose Installation

Installation and Maintenance

Temporary and Window Slider Installation

Water Full Alarm Function

Maintenance Procedures

Maintenance

Air Filter Cleaning

Air-Conditioner Surface Cleaning

Troubleshooting

Unit Not Starting

Insufficient Cooling

Noisy Operation

Error Codes (E0, E1, E2)

Related product manuals