Erbauer EBPW3000 - Care & Maintenance; Golden Rules of Care

30
Washing tips
01
General
• Dissolve dirt by applying the detergent mixed with water to the surface while still
dry. Allow the detergent to rest on the surface for a few minutes, but do not let the
detergent dry.
• When dealing with vertical surfaces, work from the bottom upwards. Use a
high pressure jet at a minimum distance of 30 cm at 45° angle from the bottom
upwards, and then rinse from the top downwards.
• For stubborn dirt, it is suggested to scrub it off with a brush prior to pressure
washing. Avoid aiming a jet on the highest setting at delicated or painted parts, or
onpressurisedcomponents(e.g.tyres,inationvalves,etc.).
• Effective washing depends on both the pressure and volume of the water used,
to the same degree.
02
Wood and vinyl decks (SOFT MODE)
CAUTION! Increase the distance from the cleaning area for softer
woods.
• Reduce your work area to smaller sections and wash each section one at a time
for optimal results.
• Rinse at high pressure using fan spray, keeping the nozzle at least 15 - 25 cm from
the cleaning surface.
• Maintain a further distance from the cleaning area when using jet spray.
03
Cement patios, stone, and brick (HARD MODE)
• Rinse at high pressure using fan spray in a sweeping motion, keeping the nozzle
at least 7 - 15 cm from the cleaning surface.
• Maintain a further distance from the cleaning area when using jet spray.
04
Cars, boats, and motorcycles (SOFT MODE)
WARNING! Do not clean the engine with this machine!
• Clean one side at a time to achieve the best results.
5063022018892-EBPW3000-PressureWasher-UM-V03.indd 305063022018892-EBPW3000-PressureWasher-UM-V03.indd 30 09-11-2022 14:09:0809-11-2022 14:09:08
31
• Rinse at high pressure using fan spray in a sweeping motion, keeping the nozzle
at least 20 cm from the cleaning surface. Do not use narrow pencil jet on vehicle
or boat paint work.
• Wipesurfacedryforapolishednish.
Care & maintenance
01
The golden rules of care
WARNING! Always squeeze the trigger lever (17a) to release the
pressure remaining in the high pressure hose (13) before cleaning,
storage or maintenance.
Always switch the machine off, disconnect it from the socket-outlet and
let the machine cool down before performing inspection, maintenance
and cleaning work!
1. Keep the machine clean. Remove debris after each use and before storage.
2. Regular and proper cleaning helps to ensure safe operation and prolongs the life
of the machine.
3. Inspect the machine before each use for worn and damaged parts. Do not operate
itifyoundbrokenandwornparts.
WARNING! Only perform repairs and maintenance work according to
theseinstructions!Allfurtherworksmustbeperformedbyaqualied
specialist!.
02
Cleaning
NOTE: Do not use chemical, alkaline, abrasive or other aggressive
detergents or disinfectants to clean this machine as they might be harmful
to its surfaces.
Machine
1. Clean the machine with a slightly damp cloth and mild soap. Use a brush for areas
that are hard to reach.
2. In particular, clean the air vents after every use with a cloth and a brush.
3. Remove stubborn dirt with high pressure air (max. 3 bar).
5063022018892-EBPW3000-PressureWasher-UM-V03.indd 315063022018892-EBPW3000-PressureWasher-UM-V03.indd 31 09-11-2022 14:09:0809-11-2022 14:09:08
96456_IM_Erbauer 3000_EU.indb 3196456_IM_Erbauer 3000_EU.indb 31 2023/3/27 上午11:082023/3/27 上午11:08