Esatto EHPD80 - Appliance Installation Guide; Transport and Handling Precautions; Installation Positioning Requirements; Final Setup and Power Connection

esatto.house
9
Instlltion
IMPORTANT!
If the power cord is damaged, it must be replaced by Residentia Group or one of it’s authorised service representatives.
Please contact 1300 11 HELP (4357) and ensure the appliance is completely disconnected from the power supply.
TRANSPORT
Move cautiously. Do not grasp any salient parts of machine. The machine door cannot be used as the handle for transport.
If the dryer can't be transported upright the dryer can be tilted at an angle less than 30°.
Risk of injury and damage! Improper handling of the appliance may result in injury.
• The appliance is very heavy. Never transport or carry the appliance alone; always with the assistance of another person.
• Remove all obstacles on the transport route and from the installation location, e.g. open doors and clear away objects
lying on the oor.
• Do not use the open door as a handhold.
• Remove all package material before using the appliance.
• Before setting up the tumble dryer, check it for any externally visible damage.
Do not install or use a damaged tumble dryer.
• Do not install the tumble dryer in a room where there is a risk of frost occurring. At temperatures around freezing point
the tumble dryer may not be able to operate properly. There is a risk of damage if the condensed water is allowed to
freeze in the pump and hoses.
INSTALLATION POSITIONING
• Children can become entangled in the packaging lm or swallow small parts and suocate. Do not allow children to
play with the packaging.
• The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to
that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.
• Do not restrict the oor clearance through deep pile carpets, strips of wood or similar. This might cause heat built-up
which would interfere with the operation of the appliance.
1. It is recommended that, for your convenience, the machine is positioned close to your washing machine.
2. Do not stack this dryer on washing machine without stacking kits. (If you want to stack this dryer on a washing machine,
please purchase the independent parts. Installation shall be done by the manufacturer, its service agent or similarly
qualied persons to avoid any hazards.)
3. The tumble dryer must be installed in a clean place, where dirt does not accumulate. Air must be able to circulate freely
around the appliance. Do not obstruct the front air inlet or the air intake grilles at the back of the machine.
4. To keep vibration and noise within minimum level when the dryer is in use, it must be placed on a rm and level surface.
5. The feet must never be removed.
LEVEL ADJUSTING
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit level.
If it is not, adjust the feet by hand or using a tool.
POWER SUPPLY CONNECTION
1. Make sure that the voltage of the power supply is the same as the electric specication.
2. Do not connect the dryer with the power connection board, a universal plug or socket, do not use multi-plug adapters
and extension cables.
11
INSTALLATION
Level Adjusting
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit level.
If it is not, adjust the feet by hand or using a tool.
Power Supply Connection
4. To keep vibration and noise within minimum level when the dryer is in use, it must
be placed on a firm and level surface.
5. The feet must never be removed.
1.Make sure that the voltage of the power supply is the same as the electric specification.
2.Do not connect the dryer with the power connection board, a universal plug or socket,
do not use multi-plug adapters and extension cables.
11
INSTALLATION
Level Adjusting
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit level.
If it is not, adjust the feet by hand or using a tool.
Power Supply Connection
4. To keep vibration and noise within minimum level when the dryer is in use, it must
be placed on a firm and level surface.
5. The feet must never be removed.
1.Make sure that the voltage of the power supply is the same as the electric specification.
2.Do not connect the dryer with the power connection board, a universal plug or socket,
do not use multi-plug adapters and extension cables.