Esco systeQ-M-SL-ESC User Manual

www.esco-online.de
Montage-, Bedienungs- und Wartungsanleitung
Installation, operation and maintenance instructions
systeQ-M-SL-ESC systeQ-M-SLH-ESC
systeQ-M-SLM-ESC systeQ-M-SLH-M-ESC
noch nicht lieferbar
esco-MBW12/01.19-10 03/2019
DE | EN
esco-MBW12/05.20-13
WICHTIG
Bei der Installation müssen die Anweisungen zur
Befestigung sorgfältig beachtet werden. Für systeQ-
M-SLM-ESC / systeQ-M-SLH-M-ESC ist die ergänzende
Montage-, Bedienungs- und Wartungsanleitung
esco 97-837431 zu beachten, siehe auch www.
esco-online.de.
Die aufgeführten Punkte dienen als Ergänzung zu
der esco Information zur Produkthaftung für Türver-
schlüsse, siehe www.esco-online.de. Bauherren und
Benutzer sind auf deren Einhaltung hinzuweisen. Bei
Nichteinhaltung dieser unbedingt erforderlichen Hin-
weise kann keine Gewährleistung für die einwandfreie
Funktion der Schlösser gegeben werden.
Die gemäß EN 179/1125 geprüften Verschlüsse dür-
fen nur mit den zertizierten Komponenten verwendet
werden, siehe unsere Website www.esco-online.de.
Andernfalls kann keine Gewährleistung übernommen
werden. Bei Verwendung eines Panikstangenbeschlag-
es ist dieser je nach Material der Tür ausreichend und
dauerhaft zu befestigen, z. B. mit Blind-Einnietmuttern.
Die Montage und korrekte Einstellung sollte von einem
Fachbetrieb vorgenommen werden.
Als Riegelschaltkontakt für die Anwendung mit ein-
er Einbruchmeldeanlage (EMA) ist ausschließlich der
esco Riegelschaltkontakt 25-806266 zu verwenden.
Aufgrund des automatisch ausfahrenden Riegels kön-
nen Fremdprodukte zu Funktionsstörungen führen.
IMPORTANT
The xing instructions must be carefully taken into
account during installation. The supplementary in-
stallation, operation and maintenance instructions
esco 97-837431 for systeQ-M-SLM-ESC / systeQ-M-
SLH-M-ESC are to be adhered, refer to www.esco-
online.de.
The points raised here provide supplementary information
to the esco Product Liability Information for door locks,
see www.esco-online.de. Its compliance is to be pointed
out to both builders and users. In the event of non-com-
pliance with these imperative instructions, faultless lock
operation cannot be warranted.
The locks tested in accordance with EN 179/1125 may only
be used in conjunction with certied components, other-
wise no warranty can be adopted; refer to our website
www.esco-online.de for further details. When using panic
bar hardware and depending on the door material, this is
to be adequately and permanently xed e.g. with blind riv-
eting nuts. The installation and correct adjustment should
be carried out by a specialist company.
As a bolt switch contact for use with intrusion detection
systems the bolt switch contact 25-806266 from esco has
to be used exclusively. Due to the automatically extending
deadbolt third-party products can cause a malfunction.
Leistungserklärung gemäß BauPVo 305/2011 siehe www.esco-online.de
For declaration of performance according to CPR 305/2011 see www.esco-online.de

Esco systeQ-M-SL-ESC Specifications

General

Finish	Satin Chrome
Keyway	Schlage C
Door Thickness	1-3/4 inches
Latchbolt Throw	1/2 inch
Deadbolt Throw	1 inch

Summary

Important Information

Installation and Fixing Instructions

Carefully observe installation instructions for mounting.

Product Liability Information

Supplementary points to product liability information for door locks.

Certified Components Usage

Use EN 179/1125 tested locks only with certified components.

Professional Installation

Installation and correct adjustment should be done by specialists.

Bolt Switch Contact Usage

Exclusively use esco bolt switch contact 25-806266 for EMA.

Operation and Locking Function

Single-leaf Operation

Details on panic function E and B for single-leaf doors.

Double-leaf Operation

Details on panic function E and B for double-leaf doors.

Controlled Latch Locking

Describes activation and deactivation of the controlled latch locking feature.

Panic Function B - Lever Handle Control

Instructions for activating/deactivating the outside lever handle for Panic Function B.

Technical Details

Door Dimensions and Weight

Specifications for door sash height, width, and sash weight.

Door Lock Identification Marking

Panic and Emergency Exit Hardware

Information on EN 1125 and EN 179 conformity for panic/emergency exit hardware.

CE Marking and Product Codes

Details on CE conformity and product codes for specific lock models.

VdS-Approved Locking Systems

Cylinder and Door Plate Requirements

Requirements for VdS-approved cylinders and burglar-resistant door plates.

Key Security and Loss

Guidelines for secure key storage and procedures for key loss.

Component Class Requirements

Table detailing required component classes based on lock class.

Installation and Fixing Instructions

General Installation Guidelines

Applicable for single/double-leaf elements, parallel run, and double-leaf checks.

Cylinder and Drilling Requirements

Specifications for profile cylinder installation, casing, and drilling.

Pre-installation Checks

Instructions for removing impurities and fixing faceplates/strikers.

Final Checks and Sealing

Ensuring soft closing, proper striker engagement, and door gasket impact.

Motor Drive Installation

Upgrade Procedure

Steps to upgrade systeQ locks with a motor drive for motorized unlocking.

Lock Mechanism Adjustments

Latch Switching and Changing

Instructions for switching and changing latches for double-leaf panic locks.

Strike Plate with Magnet

Details on strike plates with magnets and compatibility.

Strike Plate Adjustment

Procedure for adjusting standard/one-piece strike plates.

Maintenance

Regular Component Checks

Check safety-relevant hardware for wear, security, and function monthly/after 20,000 cycles.

Lubrication and Obstruction Checks

Lubricate moving parts, check keepers for obstructions, and verify no extra locks added.

Component and Operating Element Checks

Periodically check system components and operating element tightness.

Operating Force Measurement

Measure and record operating forces for releasing the lock.

Cleaning and Service Recommendations

Use specific agents; recommend service contract with authorized specialist.

Servo Technology Usage

Wiring and Connections

Terminal descriptions for servo technology wiring and required cable.

Locking Position Monitoring

System Availability and Cylinder Dimensions

Information on profile/round cylinder availability and Swiss round cylinder dimensions.

Wiring for Monitoring Functions

Details on wiring for monitoring deadbolt, cylinder, and lever-handle positions.