Name: EURA DRIVES E800-0015 S2
Brand: EURA DRIVES
Rating: 5 (1 reviews)

To Next Page

www.euradrives.eu

E800 – Rev.01 -EN- SOFT Rev. 2.04

Safety instructions Installation

& operating manual

FREQUENCY INVERTER

E800

0,2kW – 110kW (IP20)

ENGLISH

Table of Contents2
Index2
Common Installation3
Common4
Specified Application of Frequency Inverters4
Observe Specific Standards and Rules4
Handling, Transportation and Storage5
Installation of the Inverter5
Long Motor Leads6
Electrical Wiring of Frequency Inverters6
Insulation Testing7
Potential Equalization7
Braking Resistors8
Differential Current Braker (FI)8
Basic Rules for Reliable and Safe Operation9
Inverter Protection-Functions9
Measurements on Inverter Input and Output10
Power-Grid Specification10
Power Supply – Short Circuit Capability10
EMC: Basics and Recommendations for Installation11
EMC - Adequate Installation11
Twist All Unshielded Cables11
Product Data / Product Range13
- Product Naming Convention13
- Options Identifier13
- Nameplate13
- Mechanical Construction14
- Technical Data – Inverter Series E80016
- Product Range - Framesize17
- Inverter 400V – 3 Phase17
- Inverter 230V – 1 Phase17
- Inverter 230V – 3 Phase17
- Maintenance and Service18
- Mounting in Cabinet18
Inverter Mounting18
- Electrical Connection of E800 Inverters19
- 230V Singlephase19
- Power Terminals19
- 230V Threephase19
- 2014 EURADRIVES EUROPE Gmbh19
- 400V Threephase20
- 2014 EURADRIVES EUROPE Gmbh20
- 400V Threephase above 30 Kw21
- Brake Resistor21
- 2014 EURADRIVES EUROPE Gmbh21
- Recommended Cable Cross Sections, Fuses22
- Earth/Ground Connection22
- Minimum Earth/Ground Wiring Cross Section – for Terminal Connection22
- 2014 EURADRIVES EUROPE Gmbh22
- 2014 EURADRIVES EUROPE Gmbh23
- Inverter Size C3 – C623
- Control Terminals – Control Board23
- Control Terminal Function and Factory Default Configuration24
- 2014 EURADRIVES EUROPE Gmbh24
- Sample Set-Up for Inverter, 400V - Framesize25
- 2014 EURADRIVES EUROPE Gmbh25
- Control-Board: Hardware and I/O Channel Configuration26
- Digital Input Channels26
- Analogue Input Channels27
- Digital Output Channels28
- Analogue Output Channels28
- Control-Board Inverter29
- Digital Output Channels:31
- Analogue Output Channels:31
- Motor Protection with PTC/KLIXON31
- 7-Segment Display:32
- Status LED32
- Keys and Functions32
Operating Panel32
- Display of Function Parameters and Error Codes33
- Remote Operating Panel33
- Parametrization34
- Selection of Parameters, Modification and Saving34
- Parameter Types34
- Parameter Group 100: Basic Parameters35
- Dead Time During Reversion (Sec.)36
- Reverse Operation Disable36
- Cut-Off Frequency Window A,B (Hz)37
- Jog Frequency (Hz)37
- Cut-Off Frequency A,B (Hz)37
- Display Configuration:37
- Transmission Ratio38
- Pulley Diameter38
- Slip Compensation in V/Hz Mode39
- Lineare Increase39
- Quadratic Increase39
- Power Supply Voltage Compensation40
- BOOST Intensity (%)40
- PWM Frequency40
- BOOST-Kneefrequency (Hz)40
- START / STOP / Running Direction41
- Rotation Direction Preset41
- Selection of Speed Reference Sources41
Parameter Group 200: Inverter Control41
- Two / Three Wire Control for START – STOP - Rotation44
- “STOP” Mode Selection45
- Status Memory with45
- Autostart after Power-Down45
- Inverter-Error AUTO-RESET45
- Function Mapping for Digital Output Channels46
Parameter Group 300: Digital I/O Configuration46
- Activation and Configuration of the "S" Shaped Ramp47
- Frequency Threshold Setting47
- Current Threshold47
- Function Mapping for Digital Input Channels48
- Table of Digital Input Functions48
- Fixed-Frequencies Selection – Table 300-149
- Accel./Decel. Ramp Selection - Table 300-249
- Parameter Group 400: Analogue I/O Channel Configuration50
- Configuration of Analogue Speed Reference Channels50
- Non-Linear Characteristic for Analogue Channels52
- Analogue Output Configuration53
- Programming of the Individual Fixed-Frequencies54
Parameter Group 500: Fixed-Frequency, Automatic Cycling Frequencies54
- DC-Brake Function Parameters55
- Parameter for DC-Brake Control55
- Current- Voltage Limiting Functions55
Parameter Group 600: DC-Bake Control / Aux. Functions55
- Brake Chopper Control (Internal Brake Chopper)56
- DC-Voltage Control56
- Errorcodes (on Display)57
Parameter Group 700: Error Handling and Protection Functions57
- Fan Control Mode58
- Inverter/Motor Over-Load Protection58
- Fault History59
- Error: Event Counter59
- Protection Functions – Configuration59
- Delay for Inverter Error Trip59
- Idling Detection (Message Via Digital Output – Function Code 20)60
Parameter Group 800: Autotuning – Motor Data Programming61
Parameter Group 900: RS485 Hardware and Interface Parameters63
Parameter Group A00: PID Controller Parameter64
- PID Controller Parameter Setting66
- Emergency Functions66
- E800 Diagnosis67
- Digital Input Status Monitoring67
- Analogue Input Value Check67
- Digital Output Stimulation67

Questions and Answers:

Need help?

Do you have a question about the EURA DRIVES E800-0015 S2 and is the answer not in the manual?

EURA DRIVES E800-0015 S2 Specifications

General

Brand	EURA DRIVES
Model	E800-0015 S2
Category	DC Drives
Language	English

Related product manuals

EURA DRIVES E800-0007 S2

68 pages

EURA DRIVES E800 series

68 pages

EURA DRIVES E800-0015 S2 User Manual

Table of Contents

Questions and Answers:

EURA DRIVES E800-0015 S2 Specifications

Related product manuals