Eureka Copper Canyon 10

To Next Page

Fly poles

Roof poles

Wall poles

Component List:

1 Tent Body with Guy Ropes, 4 Wall Poles, 2 Roof Poles, 2 Fly Poles, 1 Fly, 1 Carry

Bag, 1 Stake Bag and Stakes, 1 Pole Bag

2. Assemble the shock

corded poles and divide

according to size and shape. Take

care; make sure that each pole

section is fully seated into the

next. Do not allow the sections to

snap together as this can damage

the ends. See fig 2.

1. Remove from the carry bag and separate all the components. Unroll and unfold

the fabric top side up, on a clean, dry space and open the doors. If windy, stake down

the windward corner. See fig 1.

4. Raise the tent. Start on one side and insert

the wall poles into the the elbows. At the

bottom of each pole, insert the pin/ring

(attached to the corner web) into the

bottom of each pole. See fig 5.

Repeat on the other side until the

tent is at full height and

freestanding.

5. Attach all clips to the wall poles. See fig 6.

Stake the tent down through the corner web loops. Stake opposite corners while applying tension

to smooth the floor wrinkles. It works best to do this before you add the fly. See fig 7.

6. Attach the ﬂy to the poles. Lay out the fly with the inside side up, on ground at the

front of the tent, near the door.

Fit the fly poles into the pockets sewn to the hem. The poles form an x crossing in the center of

the fly. Secure the fly to the poles by wrapping all five of the hook and loop fasteners around

the fly poles. See fig 8, 9 and 10.

7. Attach the ﬂy to the tent. Turn the fly assembly

over and align it so that the fly pole ends point to the

doors. Grasp the corners of the of the fly and drag

them up and over the roof poles to completely cover

the roof. ( This is much easier with two people. ) The

end of the poles should point out over the doors.

At the corners of the tent, reach under the fly and attach

the hook & loop straps to the wall poles just below the

elbow and down the length of the wall poles, securing

the fly in place. See fig 11.

At the bottom/corners of the tent, attach the

shockcorded J-hooks to the nylon

rings on the corner

web loops. See fig 12.

Stake out the attached guy ropes and adjust

tension with the in-line sliders. See fig 13.

ASSEMBLY INSTRUCTIONS

For the Copper Canyon 10

YOUR TENT IS READY !

fig 2

fig 1

fig 5

fig 3

fig 6

fig.11

fig.12

fig 7

fig 8

fig 9fig 10

fig 4

3. Insert both roof poles into the sleeves sewn on the tent body. They should

run corner to corner crossing in the center.

Fit one end of each into a nylon elbow attached to the roof corners at A and B. Move

to the opposite side, arch the poles and again fit into the nylon elbows at C and D.

See fig 3 and 4.

NOTE: One arm of each elbow has interior

ribs. The roof pole inserts into this ribbed

arm. The wall pole inserts into the plain

arm.

Guy Out: This tent has very large straight walls that act differently in high winds. If there are

high winds, carefully follow the guy out instructions on the back side of this sheet.

Awning: If it's raining, lower both corner awning poles to create run-off channels. Loosen

shockcord on each corner pole, lower the angle of each pole and re-tighten guy lines.

Power Port: Open zipper and run extension cord through opening. Close zipper so that it

rests next to the extension cord. Make sure the zipper cover is not twisted or tucked. The

cover must lay flat against the outside of the tent to keep out rain.

Take Down: Pull up all stakes. Release the fly's hook & loop straps. Remove ﬂy. Remove ﬂy

poles. Remove clips from wall poles and pull poles off of the pins. Remove roof poles.

Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it on tent. Roll

up both towards the open door and stow.

Sweep Out: Inside, at the bottom center of each

door is a sewn-in web loop. Pull this loop to the

outside and stake it down to provide a ready

exit for floor sweepings. See fig 14.

Options: Floor Saver and Gear Loft

fig.14

fig 13

REV B 4.09

Need help?

Do you have a question about the Eureka Copper Canyon 10 and is the answer not in the manual?

Summary

Tent Assembly and Setup

Component Preparation and Pole Assembly

Unpack, separate components, and assemble shock-corded poles.

Installing Tent Poles

Insert roof poles into sleeves and connect to elbows.

Raising and Securing Tent Structure

Insert wall poles, attach clips, and stake down the tent.

Attaching and Securing the Fly

Fit fly poles, attach fly to poles and tent, and secure guy ropes.

Tent Operation and Maintenance

Guy Out and Awning Adjustments

Instructions for managing high winds and creating run-off channels.

Power Port and Sweep Out Features

Using the power port and mechanism for clearing debris.

Tent Take Down Procedure

Steps for dismantling the tent, including poles, fly, and body.

Safety Warnings and Precautions

Electrocution and Electric Shock Hazard

Safety guidelines for using the power port with extension cords.

Flame and Heat Source Warnings

Caution against open flames and the flammability of tent fabric.

Seam Sealing and Staking

Recommendations for sealing seams and proper tent staking techniques.

Tent Care and Storage

Condensation and Ventilation

Managing condensation through proper tent ventilation.

General Pole and Tent Care

Guidelines for cleaning and maintaining tent poles and fabric.

Storage and Color Transfer

Proper storage methods and preventing color transfer.

Warranty Information

Details on product warranty coverage and service.