Eureka E61-ECO User Manual

2
TABLE OF CONTENTS
Topic
PAGE
INTRODUCTION
3
MACHINE IDENTIFICATION
3
WARNINGS
4
GENERAL WARNINGS AND RECOMMENDATIONS
4
DISPOSAL
7
TRANSPORT AND MOVEMENT
7
UNPACKING
8
LIFTING THE TANK
9
BATTERIES INSTALLATION
10
MACHINE DESCRIPTION
11
PRIMARY FUNCTIONS AND CONTROLS
13
MACHINE SETTING
19
 MOUNTING THE SQUEEGEE
19
 ADJUSTING THE SQUEEGEE
19
 MOUNTING THE ABRASIVE DISC ONTO THE DISC PAD HOLDER
20
 BRUSHES/ABRASIVE DISC INSTALLATION
20
 FILLING THE DETERGENT SOLUTION TANK
22
 ADJUSTING THE DETERGENT SOLUTION ON THE BRUSHES
23
USING THE MACHINE
23
 CHECK BEFORE USE
23
 OPERATION
24
PERIODIC SERVICING
25
 DRAINING AND CLEANING THE RECOVERY TANK
25
 CLEANING INSTRUCTIONS ECO-SYSTEM
26
 DRAINING AND CLEANING THE SOLUTION TANK
27
 CHECHING BRUSHES OR ABRASIVE DISCS
27
 CLEANING THE DETERGENT SOLUTION FILTER
28
 CLEANING THE PUMP OUTPUT PIPE FITTING
28
 CLEANING, REPLACING AND CHECKING THE INSTALLATION OF THE SQUEEGEE BLADES
29
 CLEANING THE SUCTION FILTER
31
 CHECKING THE BRUSH PLATE SPLASHGUARD
31
 CHECKING OR REPLACING FUSES
32
 CHECKING OR REPLACING FUSES IN THE INSTRUMENT PANEL
34
 CHECKING THE SEAL ON THE COVER
34
 RECHARCING BATTERIES
35
DIMENSIONAL TECHNICAL DRAWINGS
36
RECOMMENDED SPARE PARTS
37
TECHNICAL CHART
39
ALARMS
40
TROUBLE-SHOOTING CHART
41
PRODUCT WARRANTY
43
INSTALLATION FORM FOR WARRANTY APPROVAL
44
DECLARATION OF CONFORMITY
45
DATE OF THE LAST UPDATE: 15-07-11

Eureka E61-ECO Specifications

General

Brand	Eureka
Model	E61-ECO
Category	Scrubber
Language	English

Summary

GENERAL SAFETY WARNINGS AND ADVICE

DANGER SIGNS AND OPERATOR ATTENTION

Highlights operations representing a potentially hazardous situation for the operator.

CLEANING AND MAINTENANCE PROCEDURES

OPERATOR AND TECHNICIAN SAFETY PRECAUTIONS

OPERATOR RESPONSIBILITIES AND DUTIES

Defines the operator's duties for machine care, servicing, and safe operation.

UNPACKING THE MACHINE

INSTALLING BATTERIES

BATTERY SAFETY AND INSTALLATION STEPS

Essential safety warnings and steps for physically installing the batteries into the machine.

MACHINE DESCRIPTION AND COMPONENTS

MAJOR COMPONENT IDENTIFICATION

PRIMARY FUNCTIONS AND CONTROLS

CONTROL PANEL OPERATION

Details the functions and operation of the control panel and its components.

BRAKE PEDAL USAGE

CONTROL PANEL FUNCTIONS

WARNING SYMBOLS AND BATTERY INDICATORS

KEY SWITCH AND OPERATIONAL BUTTONS

Details ignition sequence, suction fan, and brush release button operations.

DRIVE ALARMS, EMERGENCY STOP AND SPEED SETTINGS

Describes drive alarms, battery status, emergency stop, and speed adjustment.

SETTING UP THE MACHINE

SQUEEGEE MOUNTING AND ADJUSTMENT

Instructions for attaching and adjusting the squeegee for optimal floor cleaning performance.

MOUNTING BRUSHES AND DISCS

Instructions for mounting abrasive discs onto the disc pad holder and machine.

BRUSH/DISC MOUNTING AND RELEASE PROCEDURES

FILLING THE DETERGENT SOLUTION TANK

USING THE MACHINE

PRE-USE CHECKS AND OPERATION STARTUP

Essential checks before use and basic steps to start operating the machine.

DETAILED OPERATIONAL PROCEDURES

PERIODIC SERVICING

RECOVERY TANK DRAINAGE AND CLEANING

SOLUTION TANK DRAINAGE AND BRUSH CONDITION CHECK

SQUEEGEE CLEANING AND BLADE REPLACEMENT

REPLACING SQUEEGEE BLADES

SUCTION FILTER CLEANING AND SPLASHGUARD CHECK

CHECKING AND REPLACING MOTOR FUSES

FRONT SWITCHBOARD FUSE REPLACEMENT

INSTRUMENT PANEL FUSE REPLACEMENT AND SEAL CHECK

RECHARGING BATTERIES

BATTERY CHARGING PROCEDURE AND SAFETY

Step-by-step instructions and safety precautions for recharging machine batteries.

TECHNICAL SPECIFICATIONS

CONTROL BOARD ALARMS AND SOLUTIONS

ALARM CAUSES AND RESOLUTIONS

Describes common alarms, their causes, and recommended solutions for TRAC/ECO versions.

TROUBLE-SHOOTING GUIDE

COMMON PROBLEMS AND SOLUTIONS

Lists common machine problems, their causes, and suggested solutions for diagnosis.

ADDITIONAL PROBLEMS AND SOLUTIONS

Continues listing common machine problems, their causes, and suggested solutions for troubleshooting.