To Next PageTo Next Page
Need help?Do you have a question about the evertz 570REM-RX8-10GE and is the answer not in the manual?
Describes the rear and front panel connectors and layout of the 570REM-RX8-10GE.
Provides guidelines for safely handling optical fiber cables to prevent damage and signal loss.
Details the steps required to physically install the 570REM-RX8-10GE module into a chassis.
Lists the supported serial digital video standards like SMPTE 424M, 292M, and 259M.
Details the specifications for serial video inputs, including number of inputs and equalization.
Describes the serial video output specifications, such as number of outputs and connector type.
Outlines the Ethernet interface and IP signaling for IP inputs.
Specifies support for audio pass-through and VANC data pass-through.
Details power consumption, voltage, and EMI/RFI compliance.
Indicates the number of slots the device occupies in different chassis.
Details chassis compatibility and available SFP modules for ordering.
Explains how to access and log into the WebEASY® interface for device configuration.
Allows setting IP address, Netmask, and Gateway for the control port.
Enables configuration of IP address, Netmask, and Gateway for data ports.
Provides status and monitoring of data port link, bitrate, and frame counts.
Displays information about the SFP module, including part number and power levels.
Shows the FPGA temperature of the module.
Allows exporting and importing configuration files for the device.
Configures system time source, timezone offset, and daylight savings.
Sets up Genlock reference and detected Genlock reference for synchronization.
Provides options to load factory configuration and reboot the card.
Displays product serial number and MAC address for license management.
Indicates the supported product features and their enabled/disabled status.
Configures output video color, frame delay, and output timing reference.
Sets the FS sync mode for 4K alignment.
Allows adjustment of H Phase and V Phase for output signals.
Displays frame delay, sub-frame delay, and total delay for frame sync status.
Configures how incoming streams are processed into outgoing streams.
Sets parameters for IP output, including source/destination IPs, ports, and DSCP.
Enables SMPTE 2110 audio and sets destination IP/UDP port numbers.
Configures RTP payload types for audio and ANC headers.
Configures MPPM mode (WAN/LAN) and link selection for packet merging.
Selects SFPs for obtaining main and backup video streams.
Sets stream alias, IP address, UDP port, and IGMPv3 mode for inputs.
Manages Gratuitous ARP mode and IP address.
Enables breakaway audio decoding and configures IP, port, and PID settings.
Monitors input state, program count, transport stream ID, and network name.
Configures program tuning mode, auto selection, and program number.
Allows manual selection of Video, PCR, VANC, and Audio PIDs.
Adjusts jitter tolerance for improved input detection resilience.
Reserved for future use.
Selects synchronization source for PCR.
Adjusts audio delay relative to video delay for lip sync.
Provides decoder uptime and restart functionality.
Selects PTP or Master PCR reference and configures failover mode.
Configures the domain number for PTP settings.
Sets IP address, UDP port, and PCR PID for Master PCR time reference.
Monitors total bitrate, null packet bitrate, PID count, sync loss, and CC errors.
Tracks IP packet drop count and bit rate.
Clears the IP packet drop count statistics.
Measures inter-packet jitter for selected links and channels.
Displays program number, PMT PID, PCR PID, and stream counts for decoders.
Shows the PID for video, frame rate, and resolution.
Displays J2K compliance mode and extended capability flags.
Sets thresholds for temperature warnings and received bandwidth.
Configures system traps and monitors system faults.
Manages decoder input traps and checks for input faults.
Describes the rear and front panel connectors and layout of the 570REM-RX8-10GE.
Provides guidelines for safely handling optical fiber cables to prevent damage and signal loss.
Details the steps required to physically install the 570REM-RX8-10GE module into a chassis.
Lists the supported serial digital video standards like SMPTE 424M, 292M, and 259M.
Details the specifications for serial video inputs, including number of inputs and equalization.
Describes the serial video output specifications, such as number of outputs and connector type.
Outlines the Ethernet interface and IP signaling for IP inputs.
Specifies support for audio pass-through and VANC data pass-through.
Details power consumption, voltage, and EMI/RFI compliance.
Indicates the number of slots the device occupies in different chassis.
Details chassis compatibility and available SFP modules for ordering.
Explains how to access and log into the WebEASY® interface for device configuration.
Allows setting IP address, Netmask, and Gateway for the control port.
Enables configuration of IP address, Netmask, and Gateway for data ports.
Provides status and monitoring of data port link, bitrate, and frame counts.
Displays information about the SFP module, including part number and power levels.
Shows the FPGA temperature of the module.
Allows exporting and importing configuration files for the device.
Configures system time source, timezone offset, and daylight savings.
Sets up Genlock reference and detected Genlock reference for synchronization.
Provides options to load factory configuration and reboot the card.
Displays product serial number and MAC address for license management.
Indicates the supported product features and their enabled/disabled status.
Configures output video color, frame delay, and output timing reference.
Sets the FS sync mode for 4K alignment.
Allows adjustment of H Phase and V Phase for output signals.
Displays frame delay, sub-frame delay, and total delay for frame sync status.
Configures how incoming streams are processed into outgoing streams.
Sets parameters for IP output, including source/destination IPs, ports, and DSCP.
Enables SMPTE 2110 audio and sets destination IP/UDP port numbers.
Configures RTP payload types for audio and ANC headers.
Configures MPPM mode (WAN/LAN) and link selection for packet merging.
Selects SFPs for obtaining main and backup video streams.
Sets stream alias, IP address, UDP port, and IGMPv3 mode for inputs.
Manages Gratuitous ARP mode and IP address.
Enables breakaway audio decoding and configures IP, port, and PID settings.
Monitors input state, program count, transport stream ID, and network name.
Configures program tuning mode, auto selection, and program number.
Allows manual selection of Video, PCR, VANC, and Audio PIDs.
Adjusts jitter tolerance for improved input detection resilience.
Reserved for future use.
Selects synchronization source for PCR.
Adjusts audio delay relative to video delay for lip sync.
Provides decoder uptime and restart functionality.
Selects PTP or Master PCR reference and configures failover mode.
Configures the domain number for PTP settings.
Sets IP address, UDP port, and PCR PID for Master PCR time reference.
Monitors total bitrate, null packet bitrate, PID count, sync loss, and CC errors.
Tracks IP packet drop count and bit rate.
Clears the IP packet drop count statistics.
Measures inter-packet jitter for selected links and channels.
Displays program number, PMT PID, PCR PID, and stream counts for decoders.
Shows the PID for video, frame rate, and resolution.
Displays J2K compliance mode and extended capability flags.
Sets thresholds for temperature warnings and received bandwidth.
Configures system traps and monitors system faults.
Manages decoder input traps and checks for input faults.
General| Brand | evertz |
|---|---|
| Model | 570REM-RX8-10GE |
| Category | Media Converter |
| Language | English |
