To Next PageTo Next Page
Need help?Do you have a question about the evertz 78908MG-10GE2 and is the answer not in the manual?
Details specific to the 7890MG-8-10GE2 model, including features and benefits.
Description of the rear panel connections and ports on the 7890MG unit.
Step-by-step guide for installing the 7890MG hardware, including static precautions.
Instructions for setting up the IP address, Netmask, and Gateway for the device.
Guidance on connecting the 7890MG unit to the VistaLINK PRO management software.
Technical specifications for the serial video interface, including connectors and standards.
Input specifications, including equalization for various signal types.
Output specifications, covering signal level, jitter, and rise/fall times.
Details on the Ethernet optical interface, including connectors and wavelengths.
Specifications for the Ethernet electrical interface, including connector and cable requirements.
Information on the trunk interface, including number of cages, connector type, and rates.
Electrical requirements for the device, specifying voltage.
Physical characteristics, detailing the number of slots for different chassis types.
Regulatory compliance information, including laser safety and EMI/RFI standards.
Overview of the system status, card type, firmware version, and uptime in VistaLINK PRO.
Configuration and status of input ports, including video type and bandwidth settings.
Configuration and status of output ports, including link mode and hitless switching.
Configuration and status for trunk ports, including IP address, netmask, and link status.
Configuration of IP streams for input and output, including multicast and filtering settings.
Monitoring trunk performance, including errored seconds and severe error thresholds.
Monitoring the status of SFP modules, including presence, type, and optical power.
Configuration of input fault traps to monitor for errors and status changes.
Configuration of output fault traps to monitor for errors and status changes.
Configuration of SFP fault traps to monitor for SFP module issues.
Configuration of trunk fault traps to monitor for link errors and bandwidth issues.
System overview within the WebEasy interface, showing card type and uptime.
Input configuration and status within the WebEasy interface, including video type and bandwidth.
Output configuration and status within the WebEasy interface, including link mode and hitless switching.
Trunk port configuration and status within the WebEasy interface, including mode and IP settings.
IP stream configuration and status within the WebEasy interface, for input and output.
Monitoring trunk performance metrics like errored seconds in the WebEasy interface.
Monitoring SFP module status and optical power in the WebEasy interface.
Notification settings for various faults and status changes within the WebEasy interface.
Procedure for updating JAR files for the VistaLINK PRO Server to add features or products.
Steps for upgrading the firmware of the 7890MG card via its web interface.
Details specific to the 7890MG-8-10GE2 model, including features and benefits.
Description of the rear panel connections and ports on the 7890MG unit.
Step-by-step guide for installing the 7890MG hardware, including static precautions.
Instructions for setting up the IP address, Netmask, and Gateway for the device.
Guidance on connecting the 7890MG unit to the VistaLINK PRO management software.
Technical specifications for the serial video interface, including connectors and standards.
Input specifications, including equalization for various signal types.
Output specifications, covering signal level, jitter, and rise/fall times.
Details on the Ethernet optical interface, including connectors and wavelengths.
Specifications for the Ethernet electrical interface, including connector and cable requirements.
Information on the trunk interface, including number of cages, connector type, and rates.
Electrical requirements for the device, specifying voltage.
Physical characteristics, detailing the number of slots for different chassis types.
Regulatory compliance information, including laser safety and EMI/RFI standards.
Overview of the system status, card type, firmware version, and uptime in VistaLINK PRO.
Configuration and status of input ports, including video type and bandwidth settings.
Configuration and status of output ports, including link mode and hitless switching.
Configuration and status for trunk ports, including IP address, netmask, and link status.
Configuration of IP streams for input and output, including multicast and filtering settings.
Monitoring trunk performance, including errored seconds and severe error thresholds.
Monitoring the status of SFP modules, including presence, type, and optical power.
Configuration of input fault traps to monitor for errors and status changes.
Configuration of output fault traps to monitor for errors and status changes.
Configuration of SFP fault traps to monitor for SFP module issues.
Configuration of trunk fault traps to monitor for link errors and bandwidth issues.
System overview within the WebEasy interface, showing card type and uptime.
Input configuration and status within the WebEasy interface, including video type and bandwidth.
Output configuration and status within the WebEasy interface, including link mode and hitless switching.
Trunk port configuration and status within the WebEasy interface, including mode and IP settings.
IP stream configuration and status within the WebEasy interface, for input and output.
Monitoring trunk performance metrics like errored seconds in the WebEasy interface.
Monitoring SFP module status and optical power in the WebEasy interface.
Notification settings for various faults and status changes within the WebEasy interface.
Procedure for updating JAR files for the VistaLINK PRO Server to add features or products.
Steps for upgrading the firmware of the 7890MG card via its web interface.
General