How to improve soil penetration with Ezee-On 1225 disc?
To improve soil penetration with your Ezee-On disc, increase the angle of the front and rear gangs. If increasing the gang angle doesn't provide the desired penetration, the disc may be too light.
What to do if the left side of my Ezee-On Farm Equipment disc cuts deeper than the right?
If one side of your Ezee-On disc is cutting deeper than the other, check the tire pressure.
Why does the rear of my Ezee-On Farm Equipment disc side draft to the right?
If the rear of your Ezee-On disc side drafts towards the right, reduce pressure on the rear gangs by raising them with the leveling crank, ensuring the front gangs are not cutting deeper than the rear. If this doesn't solve the problem, move the hitch towards the left. If the hitch cannot be moved enough, loosen the gang clamp plates and move both front and rear gangs approximately 4" towards the right.
What causes my Ezee-On 1225 Farm Equipment disc to side draft to the left?
If your Ezee-On disc side drafts to the left, increase pressure on the rear gang by lowering the rear gangs with the leveling crank. If this adjustment doesn't correct the issue, move the hitch towards the right. If the hitch cannot be moved enough, loosen the gang clamp plates and move both front and rear gangs approximately 4" towards the left.
How to stop my Ezee-On 1225 disc from pushing dirt and leaving a ridge?
To prevent your Ezee-On disc from pushing dirt and leaving a ridge, decrease the cutting angle of the front and rear gangs.
How to fix an Ezee-On 1225 Farm Equipment disc cutting too deep on the right side?
If the front outside blade on the right-hand side of your Ezee-On disc is cutting too deep, first check if the transport wheels are on the ground, gauging the discing depth. If the wheels are raised, the front end of the disc will drop, causing it to ridge on the right-hand side. Also, check the tire pressure, as lower pressure on the right-hand side can cause deeper cutting. You can also raise the front of the disc using the leveling crank. If these adjustments don't resolve the issue, place shims between the front gang beam and the left-hand side of the disc frame.
What to do if left hand gangs are leaving a furrow at outside of Ezee-On Farm Equipment disc?
If the left-hand gangs are leaving a furrow at the outside of your Ezee-On disc, move the rear gang toward the left-hand side or increase discing speed.
How to resolve ridges left by left hand gangs on Ezee-On 1225 Farm Equipment disc?
To resolve ridges left by the left-hand gangs on your Ezee-On disc, move the rear gang towards the right-hand side or decrease discing speed.
How to stop my Ezee-On 1225 Farm Equipment disc from plugging?
To prevent your Ezee-On disc from plugging, adjust the scrapers so they are fully in contact with the blades, or reduce the angle.
Checklist for dealer technician before equipment delivery.
Section for registering the product warranty after purchase.
Details of the standard twelve-month warranty coverage for products.
Information on additional warranty coverage for specific components.
Lists conditions and situations not covered by the warranty.
General responsibilities and principles for safe operation and maintenance.
Basic safety rules for operating, maintaining, and adjusting the unit.
Safety precautions specifically for the assembly process of the disc.
Details on the types and quantities of gang bearings used in different models.
Torque specifications for various bolts on the disc assembly.
Procedures for adjusting the cutting angle of the front and rear gangs.
How to adjust the side-to-side position of the front gang.
How to adjust the side-to-side position of the rear gang for proper leveling.
Steps to ensure the disc cuts evenly at the desired depth.
Adjusting the hitch for proper alignment and to prevent side drafting.
Detailed instructions on lubricating all grease points on the disc.
Step-by-step guide for attaching the wheel assemblies to the disc.
Instructions for connecting the hydraulic lift cylinder.
Procedure for mounting the gang beams to the frame.
How to attach the front and rear gang assemblies to the beams.
Instructions for mounting the scraper assemblies to the gangs.
Steps for installing the optional safety light kit.
General| Brand | Ezee-On |
|---|---|
| Model | 1225 |
| Category | Farm Equipment |
| Language | English |
To Next Page