To Next PageTo Next Page
Need help?Do you have a question about the EZiCAT 200 and is the answer not in the manual?
Identifies key components of the EZICAT 200 including indicators, display, and controls.
Explains how to switch on, battery status, sensitivity settings, and mode selection for the EZICAT 200.
Details the steps for performing a sweep search in POWER and RADIO modes to locate underground services.
Describes the EZICAT's automatic pinpointing capability for accurate service location.
Explains how to determine the direction of a detected service using the EZICAT.
Outlines the process for measuring the depth of a service using the EZICAT with an EZITRACE generator.
The EZiCAT 200 is a sophisticated underground service locator designed for efficient and accurate detection of buried utilities. This quick start guide provides essential information for its operation, ensuring users can effectively locate and trace services while maintaining safety.
The EZiCAT 200 is primarily used for locating buried services such as power cables, radio signals, and signals from 8kHz and 33kHz generators. It features an intuitive display panel that includes a battery level indicator, LED bar display for signal strength, and an LED mode indicator. A depth display shows the depth of the detected service, and it supports both Sonde/Line mode. The device is equipped with a function/mode select key and a depth key for easy operation. An on/off trigger controls the device, and a battery compartment houses the power source.
To switch on the EZiCAT 200, lift and hold the On/Off trigger. Upon activation, the device performs a start-up test, checking the display LEDs, speakers, and battery status. This ensures all components are functioning correctly before use. The EZiCAT 200 always powers on in POWER mode with maximum sensitivity, a crucial safety feature for operators. The battery light will flash when approximately 20% battery life remains, signaling that new, quality alkaline batteries should be installed.
Pressing the Function key allows the user to cycle through different detection modes: Power, Radio, 8kHz, and 33kHz Generator modes. The currently selected mode is indicated by an illuminated LED, making it easy to identify the active setting.
The central LED bar serves as a visual indicator of signal strength. As the device approaches a buried service, the display will show a rising signal, reaching a peak reading when directly over the service. This peak reading helps in precisely pinpointing the location of the utility.
For a comprehensive sweep search, first mark out the site to be scanned. In POWER mode, cross the site from left to right, keeping the EZiCAT 200 upright. It is crucial not to swing the device during this process to maintain accuracy. Any detected responses should be marked with marker paint, flags, or similar indicators. A critical safety note: never drive pegs into the ground over a detected service. After the initial pass, turn 90 degrees and repeat the sweep across the site. This process should then be repeated in RADIO mode, scanning in both directions.
The EZiCAT 200 features automatic pinpointing, eliminating the need for manual adjustments. To use this feature, walk across the service from an area of 'no detection,' through the detection area, and back to 'no detection.' As you retrace your steps, the audio signal automatically adjusts, reducing the service footprint with each pass until the service is accurately pinpointed. The visual display will show a peak reading when the device is directly over the service.
Once a service has been pinpointed, rotate the EZiCAT 200 until the signal display reduces to a minimum. This indicates the direction of the buried service, providing valuable information for mapping and excavation.
The EZiCAT 200 can indicate the depth of a service when used in conjunction with the EZiTRACE Signal Generator. To measure depth, ensure both the EZiCAT 200 and EZiTRACE are set to 33kHz. Pinpoint the service and position the EZiCAT 200 at 90 degrees to its direction. Then, press the depth key to display the depth reading. It is important to note that the displayed depth refers to the centre of the buried service.
The EZiCAT 200 provides a clear indication when battery life is low. When the battery light starts to flash, it signifies that approximately 20% battery life remains. At this point, all batteries should be replaced simultaneously with quality alkaline replacements to ensure consistent performance and accurate readings.
During sweep searches, mark out the site to be scanned and any detected responses with marker paint, flags, or similar. This practice helps in visualizing the layout of buried services. A crucial safety reminder is to never drive pegs into the ground over a detected service to prevent accidental damage or injury.
For accurate readings, especially during sweep searches in POWER mode, it is essential to keep the EZiCAT 200 upright and do not swing it. This ensures the device's sensors are correctly oriented for optimal detection.
To maintain proficiency and ensure accurate results, it is recommended to turn through 90 degrees and repeat the sweep across the site in both POWER and RADIO modes. This practice helps in confirming detections and improving user skill.
When marking responses, use marker paint, flags, or similar methods. CAUTION: Never drive pegs into the ground over the service. This is a critical safety instruction to prevent damage to buried utilities and potential hazards.
Always mark any responses with permanent marker paint, flags, or similar. CAUTION: Never drive pegs into the ground over the service. This practice ensures that the locations of buried services are clearly documented for future reference and to prevent accidents.
To enhance detection skills and ensure thorough site coverage, change to RADIO mode and repeat the process in both directions after completing the POWER mode sweep. This multi-mode approach helps in identifying a wider range of services.
General| Model | EZiCAT 200 |
|---|---|
| Type | Cable Locator |
| Manufacturer | Radiodetection |
| Display | LCD |
| Operating Frequency | 33 kHz |
| Material | ABS Plastic |
| Power Source | 6 x AA Batteries |
| Battery Life | 40 hours intermittent use |
