OPERATION
•
Appliance
has
default countdown setting
for all
functions except
BOIL.
Countdown
will
switch appliance
to
standby mode automatically when
it
reaches
zero
(refer
to
u
Using
the
timer).
•
Do not
overload
the
appliance. Overloading
the
induction
plate
(2) may
damage
the
plastic
cover
and
induction plate.
•
Do not use
induction
cooker
near
any
stove
or in any
space
with open
fire or an
environment
with
high temperature.
•
The
frying
pan
(15)
provided
is
intended
for
induction
cooker
use
only.
Do not
use
it on gas
stove.
NOTE:
•
The
appliance
has a
rated power
of
1300W.
Before
connecting
the
plug
(4) to
wall
outlet,
ensure
the
electrical circuit
is not
overloaded with other appliances.
This
appliance should
always
be
operated
on a
separate
120V,
60Hz wall
outlet.
•
Do not use
high
pressure
to
operate
the
touch controls
on the
control panel (5).
Use
finger
pad to
gently operate controls (ill. CD).
•
If no
cookware
or
incompatible
cookware
is
placed
on the
induction plate
(2)
while
temperature function
is
selected,
an
acoustic
warning
signal
is
audible.
Appliance
will
switch
to
standby after
ten
seconds.
•
Display shows countdown
/
timer
and
temperature alternately.
•
Although
the
induction plate
(2) is
made
of
scratch
and
impact
resistant
material,
do not use
sharp
objects
for
cleaning (ill.
CD) and
avoid
causing
impacts
on the
Induction plate (2).
•
All
control panel
(5)
function selections
will
produce
a
beep sound.
Operating
instructions
•
Connect
the
plug
(4) to
wall
outlet (ill.
CD).
•
Appliance
is in
standby mode, indicated
by
four blue
bars"
"
on the
display
(11).
•
Place
cookware
with
suitable
bottom
size
(5 - 8.5
inches)
on
induction
plate
(2)
(ill. CD).
Always
put
foodstuff
in
cookware before placing
it on
induction
plate (2).
•
Touch
ON/STANDBY
(7) to
turn
appliance
on. The
green indicator
light
on
the
ON/STANDBY
(7)
control lights
up
(ill. CD).
• An
acoustic
warning
signal
is
audible. Touch FUNCTION (14)
to
choose desired
temperature
setting within
ten
seconds
to
prevent appliance from switching
back
to
standby mode (ill.
OPERATION
•
Touch
FUNCTION (14)
to
choose
temperature setting from
WARM
to
SEAR.
The
display
shows
temperature according
to the
selected
function.
FUNCTION
indicator
(10)
lights
up
blue
to
indicate
selected
function.
NOTE:
Do not
select BOIL mode when using oil. Only
use oil
when selecting FRY,
GRILL
and
SEAR
mode.
•
Touch
+
control
(9) or -
control
(12)
to
adjust
temperature
of
selected
functions.
Refer
to
below table
for
possible
options.
•
Touch
PAUSE
(8) to
stop heat transfer
and to
hold
the
timer
or
countdown.
•
Touch
PAUSE
(8)
again
to
resume
heat
transfer
and
timer
or
countdown.
Touching
PAUSE
(8)
will
not
reset
timer
or
countdown.
•
After
foodstuff
is
prepared, touch
ON/STANDBY
(7) to
enter standby mode.
The
green indicator
light
will
turn
off. Four
blue
bars"
"
on the
display
(11)
will
flash
to
indicate
the
appliance
has not
cooled down. After cooling down,
the
four blue
bars"
"will
be
permanently shown
on the
display.
•
Disconnect
the
plug
(4)
from
the
wall
outlet
after
use
(ill.
CD).
NOTE:
If
cookware
is
removed
during
operation,
the
appliance
will
stop heating
immediately.
Place
cookware
within
about
10
seconds
to
resume
cooking,
otherwise
the
appliance automatically switches
to
stand-by mode.
Function
Control Default +/- Control
temperature
WARM
SIMMER
BOIL
FRY
:.
.
Touch
FUNCTION
once
Touch
FUNCTION
twice
Touch
FUNCTION
three times
Touch
FUNCTION
four times
140°F
203°F
212°F
325°F
N/A
N/A
N/A
Touch
+
control
or
-
control
to
adjust
temperature
in
steps
of
25°F.
Temperature range
from
275°F
to
375°F
To Next Page
Loading...
Need help?
General