EasyManua.ls Logo

Farmi Forest Mastersplit WP30 - User Manual

Default Icon
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Farmi Forest Corporation
Ahmolantie 6
FIN-74510 Iisalmi, Finland
Tel. +358 (0)17 83 241
Fax. +358 (0)17 8324 372
www.farmiforest.
MASTERSPLIT
WP30
OPERATING MAINTENANCE AND SPARE
PARTS MANUAL
PLEASE READ THIS OPERATING AND MAINTENANCE MANUAL CAREFULLY BEFORE OP-
ERATING THE MACHINE
STARTING FROM THE SERIAL NO. 10420
THIS MACHINE MAY BE OPERATED ONLY BY ONE PERSON
AT THE TIME!
MORE THAN ONE PERSON WORKING SIMULTANEOUSLY IS
STRICTLY FORBIDDEN.
45302100 B-EN-131211-NKU

Table of Contents

Questions and Answers

  • S
    Sandra EllisAug 10, 2025
    Why is my Farmi Forest Mastersplit WP30 Log Splitter hydraulic oil overheating or chainsaw rotation faulty?
    • S
      Stephanie LeeAug 10, 2025
      Hydraulic oil overheating or chainsaw rotation faults in your Farmi Forest Log Splitter can occur due to several reasons: using rapid action with large wood, having too great a revolution speed, or an issue with the chainsaw valve shaft position. Check the tractor’s power output revolution number, ensuring it doesn't exceed the maximum allowed. Also, inspect the chainsaw valve and the angle of the flap, adjusting the flap position correctly using the hex screw on the chainsaw frame.
  • F
    fosterleviAug 15, 2025
    What to do if my Farmi Forest Mastersplit WP30 Log Splitter combustion engine has starting problems?
    • S
      Sherry TurnerAug 15, 2025
      If you're experiencing starting problems with your Farmi Forest Log Splitter's combustion engine, there are a few potential causes. First, check for water in the fuel system and drain any trapped water by opening the fuel filter/drain plug. Second, if the conveyor belt is jammed and causing considerable resistance, fold the conveyor extension part to loosen the belt. Finally, ensure you are using the correct starting method.
  • C
    Christina LivingstonAug 21, 2025
    How to fix a slipping conveyor belt on my Farmi Forest Mastersplit WP30 Log Splitter?
    • S
      Sean StanleyAug 21, 2025
      A slipping conveyor belt on your Farmi Forest Log Splitter can be due to a few reasons. The conveyor belt might be loose, in which case you should tighten it. If the conveyor belt rotates unevenly or rubs against the sides, carefully tighten the adjusting nut on the affected side. Also, check for and remove any impurities from the conveyor belt and driving roller.
  • S
    Sean GoodmanAug 26, 2025
    What to do if my Farmi Forest Log Splitter electric engine has problems?
    • J
      josephcummingsAug 26, 2025
      If you're encountering electric engine issues with your Farmi Forest Log Splitter, begin by verifying the electric switch position. Start the electric engine by turning the switch to the “Y” position, and then immediately turn it back to the “?” position once the engine starts. Also, check the power transmission and cables for any incorrect couplings.
  • J
    jamescooperAug 31, 2025
    What causes chainsaw lubrication fault in Farmi Forest Mastersplit WP30 Log Splitter?
    • S
      sheltonmelissaAug 31, 2025
      A chainsaw lubrication fault in your Farmi Forest Log Splitter is caused by an incorrect adjustment of the lubrication cylinder. To resolve this, you need to perform an adjustment of the lubricator.
  • T
    Tracy FloresSep 4, 2025
    What does it mean if the oil thermometer is defected on my Farmi Forest Mastersplit WP30?
    • G
      Gail PerezSep 4, 2025
      If the oil thermometer is defected on your Farmi Forest Log Splitter, it indicates that the oil has overheated, causing the gauge to expand and break the thermometer.

Farmi Forest Mastersplit WP30 Specifications

General IconGeneral
CategoryLog Splitter
Splitting Force30 tons
ModelFarmi Forest Mastersplit WP30
Max Log Length630 mm
Max Log Diameter12 inches
Cylinder Stroke580 mm
Oil Tank Capacity30 l
Wheel Size4.80-12
Hydraulic Oil Capacity24 l

Related product manuals