Farmi Forest Mastersplit WP36

Questions and Answers

P
phillipsstephanieAug 8, 2025
Why is my Farmi Forest Mastersplit WP36 Log Splitter hydraulic oil overheating or chainsaw rotation faulty?
- V
  Victoria BrownAug 8, 2025
  Hydraulic oil overheating or chainsaw rotation faults in your Farmi Forest Log Splitter can occur due to several reasons: using rapid action with large wood, having too great a revolution speed, or an issue with the chainsaw valve shaft position. Check the tractor’s power output revolution number, ensuring it doesn't exceed the maximum allowed. Also, inspect the chainsaw valve and the angle of the flap, adjusting the flap position correctly using the hex screw on the chainsaw frame.
L
lmorganAug 13, 2025
What to do if my Farmi Forest Log Splitter combustion engine has starting problems?
- J
  jamesnguyenAug 13, 2025
  If you're experiencing starting problems with your Farmi Forest Log Splitter's combustion engine, there are a few potential causes. First, check for water in the fuel system and drain any trapped water by opening the fuel filter/drain plug. Second, if the conveyor belt is jammed and causing considerable resistance, fold the conveyor extension part to loosen the belt. Finally, ensure you are using the correct starting method.
W
Walter LuceroAug 17, 2025
How to fix a slipping conveyor belt on my Farmi Forest Log Splitter?
- S
  Sheryl CooperAug 17, 2025
  A slipping conveyor belt on your Farmi Forest Log Splitter can be due to a few reasons. The conveyor belt might be loose, in which case you should tighten it. If the conveyor belt rotates unevenly or rubs against the sides, carefully tighten the adjusting nut on the affected side. Also, check for and remove any impurities from the conveyor belt and driving roller.
P
patrick68Aug 22, 2025
What to do if my Farmi Forest Mastersplit WP36 electric engine has problems?
- B
  Brian HaasAug 22, 2025
  If you're encountering electric engine issues with your Farmi Forest Log Splitter, begin by verifying the electric switch position. Start the electric engine by turning the switch to the “Y” position, and then immediately turn it back to the “?” position once the engine starts. Also, check the power transmission and cables for any incorrect couplings.
W
whicksAug 27, 2025
What causes chainsaw lubrication fault in Farmi Forest Mastersplit WP36 Log Splitter?
- P
  Parker SharpAug 27, 2025
  A chainsaw lubrication fault in your Farmi Forest Log Splitter is caused by an incorrect adjustment of the lubrication cylinder. To resolve this, you need to perform an adjustment of the lubricator.
N
nbarrettSep 1, 2025
What does it mean if the oil thermometer is defected on my Farmi Forest Log Splitter?
- S
  Steven BaileySep 1, 2025
  If the oil thermometer is defected on your Farmi Forest Log Splitter, it indicates that the oil has overheated, causing the gauge to expand and break the thermometer.

Summary

General Information, Safety, and Labels

Machine Operation Principles and Safety Symbols

Explains machine operation, rules, and the meaning of safety symbols.

Safety Instructions and Warnings

Provides essential general and specific safety rules for machine operation.

Machine Labels and Identification

Details important labels for operation, safety, and machine identification.

Machine Setup, Operation, and Accessories

Commissioning Procedure Overview

Steps for initial machine setup, strap removal, and component connection.

Wood Loader and Splitter Operation

How to operate the wood loader and additional wood splitter.

Splitting Adjustments and Working Methods

Adjusting splitting parameters and operational techniques.

Pre-Operation Checks and Working Method

Essential checks and procedures before starting operation.

Transport, Maintenance, and Troubleshooting

Preparing for Hauling and Road Driving

Steps to prepare the machine for transport and road driving.

Maintenance, Lubrication, and Disposal

Procedures for maintenance, lubrication, and machine disposal.

Troubleshooting Common Issues

Guide to diagnosing and resolving common machine problems.

Technical Specifications and Parts Lists

Machine Specifications and Labels

Details machine specs, labels, and dimensions.

Hydraulics, Frame, and Chainsaw Components

Lists components for hydraulics, frame, and chainsaw assemblies.

Engines, Conveyor, and Transportation Base Parts

Lists components for engines, conveyor, and transport base.

Warranty and Registration

Warranty Information

Details the manufacturer's warranty terms and conditions.