Farmnavigator G7 - Page 2

1. Introduction 4
1.1 Ways of using G7 4
1.2 Electrical connections 4
1.3 How to install a FARMNAVIGATOR
antenna 5
1.3.1 How to connect a FARMNAVIGATOR
antenna to G7 5
1.3.2 Antenna position – Transverse axis 5
1.3.3 Antenna position - Longitudinal axis 6
1.3.4 Antenna position – Height 6
1.3.5 Antenna position - Orientation 6
1.4 Turning the device on 7
1.5 How to use multi-touch display 8
2. Main menu and basic operations 9
2.1.1 DRIVERS 10
2.1.2 FARMERS 11
2.1.3 FIELDS 12
2.1.4 PRODUCTS 13
2.1.5 JOBS 13
2.1.6 IMPLEMENTS 13
2.1.7 TASKS ISOXML 19
2.2 New Job 21
2.3 Continue / Close Last Job 25
2.4 Setup 27
2.4.1 Satellites 27
2.4.2 GPS antenna position on the tractor 31
2.4.3 Auto Steering
(for G7 Plus and G7 Iso) 32
2.4.4 ISOBUS 33
2.4.4.1 VIRTUAL TERMINAL
conguration 34
2.4.4.1.1 VIRTUAL TERMINAL 34
2.4.4.1.2 VIRTUAL TERMINAL ID 34
2.4.4.1.3 AUX setting 34
2.4.4.1.4 Transmit GPS Speed 35
2.4.4.1.5 Object pool 35
2.4.4.1.6 Messages LOG 35
2.4.4.2 TASK CONTROLLER
conguration 36
2.4.4.2.1 TASK CONTROLLER 36
2.4.4.2.2 Total TASK CONTROLLER 36
2.4.4.2.3 TASK CONTROLLER LOG 36
2.4.5 Navigation activation
(only for G7 Terminal) 37
2.4.6 Guidance 37
2.4.7 Work view layout 38
2.4.8 Units 39
2.4.9 User preferences 40
2.4.10 Remote control 40
2.4.11 Wireless connectivity (for G7 Plus,
G7 Iso and G7 Terminal) 42
2.4.12 Remote access (for G7 Plus,
G7 Iso and G7 Terminal) 43
2.4.13 General Settings 44
2.4.14 System Information 45
2.4.15 VIRTUAL TERMINAL Menu 45
2.5 MyFarmnavigator Menu 47
3. Job page 49
3.1 Current Job information 49
3.1.1 Job name 49
3.1.2 Connected devices 49
3.1.3 Antenna precision and reception 50
3.1.4 Zoom Level and compass 50
3.1.5 Area, speed, distance 51
3.2 Operative functions during job 51
3.2.1 Start/Stop 51
3.2.2 A-B lines 51
3.2.3 Field 54
3.2.4 Headland 56
3.2.5 Obstacles 58
3.2.6 Auto Steering system (For G7 Plus
and G7 Iso) 59
3.2.7 Nudge 60
4. Advanced operating modes 62
4.1 How to use G7 Terminal 62
4.2 Start new job, full mode 63
4.3DenetheeldandcreatenewA-B
guidelines 63
4.4WorkingagainondenedA-Blines
using the same implement 64
4.5WorkingonpredenedA-Blinesbut
with another implement 65
4.6 Create more than one A-B line during
the same job session 66
4.7 Change A-B lines during the same job 67
4.8Movethelinetoaspecicpoint,
“Magnet” function 69
4.9 Move A-B line according a precise value,
“Street” function 69
4.10 Connect an external device to
control sections 69
4.11 How to activate the free VT and TC
trial (G7 Iso, G7 Terminal, Iso Kit) 77
4.12 How to connect an ISOBUS
instrument 78
Index