Fellowes Galaxy 500 - Troubleshooting Guide; Punched Holes Not Central; Machine Will Not Punch; Holes Not Parallel to Edge

CORRECTING A BOUND DOCUMENT
Additional sheets may be included or removed at any time by opening and then closing the comb as previously described.
REMOVAL OF WASTE CLIPPINGS
The waste tray is located under the machine and is accessed from each side. For best results empty the troy regularly. The troy
should be emptied after every 50 operations to ensure no blockages occur.
STORAGE
lower the lid and punch handle. The Galaxy comb binder is designed to be stored horizontally on the desk.
TROUBLESHOOTING
Problem
Cause Solution
Punched holes are not centrol Edge gUide not set Adjust edge gUide until hole pallern is correct
Machine will not punch Blockage Check waste troy in empty. Check for blockage to paper entry
Punch holes are not parollelto edge
Debris is stuck below dies
Take stiff cardboard and slide into the paper entry. Move the
cardboard sideways to release any stroy clippings into the
waste troy
Partial holes
Sheets not correctly aligned to punch pallern Adjust edge gUide and test punch scrap sheets until correct
Missing holes
Selectable dies are not selected to punch Check the correct dies are selected to punch holes. To select a
die, push selector switch down at the front
Sheets will not turn on the
Back margin is too large for a smaller comb Select the smaller margin depth for combs up to 18mm (11/16")
bound document in diameter (2-150 sheets) Select the larger margin depth for
combs larger than 18mm (11/16") in diameter (151-500 sheets)
Damaged hole edges
Possibly overloading the machine
Punch plastic covers with paper sheets. Reduce number of
sheets being punched
Waste troy leaks
Waste troy is not correctly inserted or 'burst Check waste troy is empty and 'burst feature' is closed
feature' has activated
WORLDWIDE WARRANTY
Fellowes warrants all parts of the binder to be free of defects in material and workmanship warranty period set forth above. In no event shall Fellowes be liable for any consequential
for 2 years from the date of purchase by the original consumer. If any part is found to be damages attributable to this product. This warranty gives you specific legal rights. You may
defective during warranty period, your sale and exclusive remedy will be repair or replacement, have other legal rights that vary from this warranty. The duration, terms and conditions of this
at Fellowes' option and expense, of the defective part. This warranty does not apply in warranty are valid worldWide, except where different limitations, restrictions or conditions may
cases of abuse, mishandling or unauthorised repair. Any implied warranty, including that of be required by local law. For more details or to obtain services under this warranty, please
merchantability or fitness for particular purpose, is hereby limited in duration to the appropriate contact Fellowes or your dealer.
s
CORRECTING A BOUND DOCUMENT
Adllilionol shee~ may be included or IEmoved at ony lime by opening and then dosing the comb os previovsly desaibed.
REMOVAL OF WASTE CLIPPINGS
The wasle Iroy is lo<oled under Ihe ma<hine ood is (J(ces'led from eom side. For be5lrewlts empty the "oy reguhlly. The tray
should be emplied oher every 50 opelalions 10 el15llre no blodtoges O«UI.
STORAGE
Lower the lid ood plJlKh hondle. The GoIoKY comb bilder is d~gned 10 be stored horizontally on the desk.
TROUBLESHOOTING
Problem
Punched holes ole nol (enlral
Ma(hine will no! punch
PulKh holes ore no! porollello edge
Partial holes
Missing holes
Sheels will 1101 Ium on lhe
bound documenl
Damaged hole edges
WIlSIe Iray leaks
WORLDWIDE WARRANTY
(ouse
Edge guide no! sel
Blockage
Debris is sllJ(k below dies
Sheels nol (orred~ atl!lned 10 pUlKh panem
Selectable dies are nol seleded 10 pUlKh
Back RlOlgin is 100 !luge fOf a smaller (omb
Possib~ ovelloading Ihe machine
Wasle hay is nol (orred~ inserted Of'bunl
feolure' has activaled
Solution
Adjvsl edge guide unl~ hole pattern is COiled
Check wosIe Ilay in empty. (he<k for blockage 10 poper enlry
Toke slM (o,dboo,d ond stlde inlo the paper elllry. Move the
(o,dboord sideways 10 release ony slray <tlppings inlo the
waste flOY
Adjusl edge guide and lesl pUlKh snap sheels ulllil corred
Check Ihe correct dies ale selected 10 pUlKh holes. Toselect a
die, push seledOf swh(h down allhe honl
Seled Ihe smallel margin deplh for (ombs up 10 18mm (11M')
in diameler (2-150 sheels) Seled Ihe Iolger margin deplh for
(ombs Iolger lhan 18mm (11/16") in diamelel (151-500 sheels)
PulKh pIoslic (ovelS whh paper sheels. Reduce number of
sheels being pUlKhed
Check me Ilay is emply and 'bunl fealure' is closed
Fe!owes WIlliant> al P::II!> of tile birdel to ~ free of defect> i'I materkll ard worhoonsllip
for 2 yool$from tile date of PUlcOOse hoi the ori;lil'lll con\lJmel.lf Ol'tf p::111 is found kl De
defectite dUlirM;! wallanty peliod. yOlJ SlJ~ 000 exuusive lerre:lv wil De lepai or repklcerrent.
01 felklwes' optkln aoo e~nse. of tile de/ecme parl.lhis worlanty does rot opp~ il
cases of abuse. mislnrdlill;l or lII'lllJll1orised lepatAI'tf rnplied wOlronty. inckxling tint of
mlll(lnnlllD~ity or fimess for partkool Plllpase. is iIele/rf lmitoo il dllfOlion to tIJe applOpriote
WIllionty pilliod set fOith above. In I'll event slnll feftowes ~ mb~ for any col\SllGlIential
darooges atlliDl/IOble to this prochxt. TliswOlronty gives you SpecifK IegJI r'lJ/lts. You rooy
tnve otller leI}ll right> that vary from this WIlrranty. The duration. terms ard conditions of this
WIlrlanty are will worl:lwiJe. except where different lmitati:lns, restrictions or conditions IOOy
be rElluked hoi klcollaw. For more delllas 01 to oDlIlin servkes under thiswOlronty. please
conlllct Fellowes 01 'fOUl dooler.
,
https://www.supplychimp.com