Why does my Ferris 5901705 Lawn Mower rider steer or handle poorly?
Poor steering or handling of your Ferris Lawn Mower could be due to loose steering lever linkages; check and tighten any loose connections. It could also be caused by improper tire inflation; check the tire pressures.
Why is my Ferris Lawn Mower leaving stringers?
Your Ferris Lawn Mower may be leaving stringers because the blades are not sharp or are nicked; sharpen your blades. Another cause could be that the blades are worn down too far, so replace them. Make sure the engine speed is at full throttle and that your ground speed is not too fast; slow down if necessary.
What to do if my Ferris 5901705 engine stalls easily with the mower engaged?
If your Ferris Lawn Mower engine stalls easily when the mower is engaged: * Set the engine to full throttle. * Decrease ground speed. * If cutting tall grass, set the cutting height to maximum for the first pass. * Ensure the discharge chute isn't jamming with cut grass by cutting with the discharge pointing towards the previously cut area.
Why is my Ferris 5901705 Lawn Mower experiencing excessive oil consumption?
Excessive oil consumption in your Ferris Lawn Mower could be due to too much oil in the crankcase; drain the excess oil. Alternatively, the engine might be running too hot; clean the engine fins, blower screen, and air cleaner.
What causes uneven cutting with my Ferris 5901705?
Uneven cutting with your Ferris Lawn Mower can be caused by several factors: * The deck may not be leveled correctly; level the deck. * Blades might be dull, worn, or damaged; sharpen or replace them. * The deck could be clogged with grass clippings; clean out the deck. * The deck shell might be damaged; repair or replace the deck. * The mower spindle could be bent or loose; repair or replace the spindle. * Blades might be installed incorrectly; reinstall them correctly. * Tire inflation may be improper; check and inflate the tires.
Why does my Ferris Lawn Mower engine start hard or run poorly?
If your Ferris Lawn Mower engine starts hard or runs poorly, it could be due to a fuel mixture that's too rich. Try cleaning the air filter and checking the choke adjustment. Also, the spark plugs might be faulty, fouled, or incorrectly gapped; clean and gap, or replace them.
How to fix streaking when cutting grass with my Ferris Lawn Mower?
If your Ferris Lawn Mower is leaving streaks, try these solutions: * Sharpen or replace the blades. * Always mow at full throttle. * Slow down your ground speed. * Clean out the mower deck. * Overlap your cutting rows adequately, especially when turning.
Why is the engine exhaust black on my Ferris Lawn Mower?
Black engine exhaust on your Ferris Lawn Mower could be due to a dirty air filter, so replace it. Another possible cause is that the engine choke is in the closed position; open the choke control to resolve this.
Warns about chemicals known to cause cancer/birth defects in California.
Provides essential safety rules to prevent severe injury, death, or property damage.
Warns about tragic accidents involving children near the operating unit.
Explains hazards of operating on inclines and provides safe slope operating guidelines.
Details safe refueling practices and the importance of proper maintenance.
Lists general safety rules for operating the unit, including clearing the area and avoiding hazards.
Details tests to ensure the safety interlock system is functioning correctly.
Lists essential checks to perform before starting the engine, including fluid levels and fasteners.
Provides step-by-step instructions for starting the engine safely.
Outlines the procedure for stopping the rider and engine safely.
Guides the user on practicing zero-turn maneuvers for smooth and efficient control.
Presents a schedule for routine maintenance tasks based on operating hours.
Details safe procedures for adding fuel to the mower's tank.
Guides on changing the engine oil and filter, referencing engine options.
Details how to inspect mower blades for wear, damage, or erosion.
Guides on safely sharpening mower blades using grinders or files.
Outlines steps to properly level the mower deck for consistent cutting.
Details safety precautions and procedures for charging a dead battery.
Provides instructions and warnings for jump-starting the unit with a booster battery.
Lists causes and remedies for engine starting issues.
Provides troubleshooting steps for engines that start hard or run rough.
Troubleshoots issues where the engine runs but the rider doesn't move.
Diagnoses causes for the mower deck not lifting.
Troubleshoots engine stalling when the mower deck is engaged.
General| Engine Displacement | 724 cc |
|---|---|
| Cutting Width | 61 inches |
| Cutting Height | 1.5 - 5 inches |
| Spindle Material | Cast iron |
| Transmission | Hydro-Gear ZT-3400 |
| Speed | 10 mph |
| Engine | Briggs & Stratton |
To Next Page
