Why won't the parking brake hold on my Ferris SRS Z2?
If the parking brake will not hold on your Ferris Lawn Mower, it is likely that the brake is incorrectly adjusted. Refer to the "Parking Brake Adjustment" section for instructions.
Why does my Ferris SRS Z2 Lawn Mower engine start hard?
If your Ferris Lawn Mower engine starts hard or runs poorly, the fuel mixture might be too rich. Try cleaning the air filter. If you have a carbureted model, check the choke adjustment. For fuel-injected models, consult an authorized service dealer. Another possibility is a faulty spark plug; in that case, clean, gap, or replace it.
Why is my Ferris SRS Z2 consuming too much oil?
Excessive oil consumption in your Ferris Lawn Mower could stem from several causes. The engine might be running too hot; clean the engine fins, blower screen, and air cleaner. You might be using the wrong weight oil (refer to the engine manual). Also, there might be too much oil in the crankcase; drain the excess oil.
What to do if the mower deck drive belt slips on my Ferris SRS Z2 Lawn Mower?
If the mower deck drive belt on your Ferris Lawn Mower slips or fails to drive, it could be due to a broken or improperly attached idler pulley spring (repair or replace as needed) or a broken mower deck drive belt (replace the mower deck drive belt).
Why won't my Ferris SRS Z2 Lawn Mower engine turn over or start?
There are several reasons why your Ferris Lawn Mower engine might not turn over or start: * The parking brake might not be engaged: Engage the parking brake. * The mower might be out of fuel: If the engine is hot, allow it to cool, then refill the fuel tank. * The engine could be flooded: For carbureted models, move the choke control to the closed position. For fuel-injected models, consult an authorized service dealer. * A fuse might be blown: Replace the fuse. * The battery terminals may need cleaning: Clean the battery terminals. * The battery could be discharged or dead: Recharge or replace the battery. * There might be loose or broken wiring: Visually check the wiring and replace any broken or frayed wires. Tighten any loose connections. * A safety interlock switch co...
What to do if my Ferris Lawn Mower engine runs but it won't drive?
If the engine of your Ferris Lawn Mower runs but the mower won't drive, the transmission release lever(s) might be in the "disengaged" position. Move the transmission release lever(s) to the "engaged" position.
Why is my Ferris Lawn Mower giving a stepped cut?
Stepped cutting with your Ferris Lawn Mower can be caused by several factors. The deck might not be leveled correctly, or the tires might not be properly inflated. Additionally, the blades could be damaged, the deck shell could be damaged, or the mower spindle could be bent or loose. Finally, the blades might be installed incorrectly. Level the deck correctly, check and inflate the tires, replace the blades, repair or replace the deck, repair or replace the spindle, and reinstall the blades correctly.
Why won't the blades engage on my Ferris SRS Z2?
If the blades on your Ferris Lawn Mower won't engage, there may be electrical wiring damage (locate and repair the damaged wire). Another possibility is that the operator is not standing on the operator platform (the operator must stand on the platform and pull up on the PTO switch).
Why is my Ferris SRS Z2 engine knocking?
If your Ferris Lawn Mower engine is knocking, it might be due to a low oil level. Check the oil level and add oil as needed. It could also be caused by using the wrong grade of oil. Refer to the engine manual for the correct type of oil.
Why is my Ferris Lawn Mower leaving stringers?
Your Ferris Lawn Mower may be leaving stringers because the blades are not sharp or nicked (sharpen your blades), the blades are worn down too far (replace your blades), the engine speed is too slow (always mow at full throttle), the ground speed is too fast (slow down), or the deck is plugged with grass (clean out the mower).
Explains safety alert symbols and signal words used to identify hazards and potential injury severity.
Provides general safety rules and guidelines for operating the mower safely.
Warns about the dangers of children near operating equipment and how to prevent accidents.
Details safe operation on slopes, including maximum angles and caution.
Describes the danger of thrown objects from mower blades and how to prevent injury.
Warns about the dangers of moving parts and how to stay safe while operating.
Advises on safe clearance and operation near hazards like walls, edges, and water.
Provides guidelines for safely handling gasoline, including refueling and storage precautions.
Warns against operating the mower in enclosed spaces due to carbon monoxide risk.
Explains how to measure lawn slopes using a smartphone or angle finder.
Emphasizes operator training, familiarity with controls, and preparation before operation.
Lists key safety precautions to follow during operation, including keeping feet on platform and not leaving unattended.
Provides detailed instructions and warnings for operating the mower safely on slopes.
Details hazards related to loss of control on slopes and specific actions to avoid.
Warns about reduced traction and loss of control on wet or soft slopes.
Advises on avoiding hazards near water, walls, and drop-offs to prevent rollovers.
Highlights the risks associated with children and mowing, advising awareness and prevention.
Emphasizes safety precautions to take before and during maintenance procedures.
Outlines general practices for maintaining and storing the unit safely and properly.
Details the comprehensive steps for preparing the unit for long-term storage, including fuel and battery care.
Details the procedures for safely starting the unit after it has been stored for a long time.
Guides users to read and understand safety decals for North American models for hazard awareness.
Illustrates a warning decal about overfilling the fuel tank and potential fire hazard.
Shows a danger decal regarding amputation and thrown objects hazards.
Displays a danger decal related to stand-on operation hazards and safe practices.
Shows a warning decal about pinch point hazards, especially related to springs.
Illustrates a warning decal for amputation and pinch point hazards involving belts.
Guides users to read and understand safety decals for export models.
Displays dashboard and operator compartment decals with warnings for CE models.
Details specific tests to verify the proper functioning of the safety interlock system.
Provides an overview of the mower's controls and their functions for operation.
Identifies and describes the location and purpose of various unit controls.
Explains how to adjust the maximum forward speed bar for desired speed settings.
Describes how the ground speed control levers operate the mower's movement.
Explains the function of transmission release levers for pushing the unit.
Identifies controls on the instrument panel for fuel-injected models.
Identifies controls on the instrument panel for carbureted models.
Provides initial steps and safety checks before operating the mower for the first time.
Details the procedure for starting the engine on carbureted models, including safety warnings.
Details the procedure for starting the engine on fuel-injected models, including safety warnings.
Explains the correct procedure for stopping the mower engine and unit safely.
Guides the operator on how to drive the zero-turn mower, emphasizing practice and familiarization.
Explains how to adjust the maximum forward speed bar for customized operator control.
Details the steps for achieving smooth forward travel using the control levers.
Provides practice steps for basic forward driving and control of the mower.
Guides the operator on practicing reverse movement and safe backing.
Explains how to perform zero-turn maneuvers for turning in place.
Details how to practice turning the mower around corners.
Explains how to execute a zero-turn at the end of a row for efficient mowing.
Advises on mowing across slopes for better traction and control, including body positioning.
Provides guidance for mowing up and down slopes when mowing across is not possible.
Offers tips for optimal mowing performance and mower longevity.
Provides guidelines on the best time of day and grass conditions for mowing.
Discusses different mowing patterns for efficient and professional results.
Explains the broadcast mowing method and its optimal engine and ground speed settings.
Advises on the maximum amount of grass to cut in a single pass when broadcasting.
Details the conditions required for effective mulching, emphasizing dry grass and proper cutting amount.
Recommends engine and ground speed settings for optimal mulching performance.
Guides on the optimal amount of grass to mulch for best results.
Outlines the steps to disengage the transaxles and push the unit by hand.
Provides instructions for storing the unit for short periods, focusing on fuel safety.
Details the comprehensive steps for preparing the unit for long-term storage, including fuel and battery care.
Details the procedures for safely starting the unit after it has been stored for a long time.
Lists maintenance tasks based on operating hours: Before Each Use, Every 25 Hours, Every 100 Hours.
Emphasizes safety precautions to take before and during maintenance procedures.
Details the procedure for checking and adding fuel to the mower, including safety warnings.
Explains how to replace a dirty or clogged fuel filter, with safety precautions.
Provides instructions for checking the engine oil level before each use.
Notes specific oil type and capacity for Vanguard engines with remote oil tanks.
Details the process for changing the engine oil and filter on models with a remote oil tank.
Addresses containing fluids during maintenance and proper disposal of waste.
Briefly explains EFI system monitoring and when to consult a dealer.
Provides instructions for cleaning the engine compartment using air and water.
Details inspection of the muffler and spark arrester for damage or blockage.
Identifies the location and amperage of the unit's two replaceable fuses.
Details the procedure for checking and filling transmission oil levels.
Outlines the procedure and interval for changing the transaxle oil filter.
Explains the critical procedure for removing air from the hydraulic system to ensure proper function.
Advises on periodically checking and maintaining tire pressures for optimal performance.
Lists various points on the unit that require lubrication, including grease and oil points.
Provides instructions on how to safely remove mower blades, including safety precautions.
Guides on inspecting, sharpening, and balancing mower blades for optimal cutting performance.
Details the correct procedure for installing mower blades, including torque specifications.
Provides step-by-step instructions for setting the cutting height.
Explains the neutral system function and how to check its adjustment.
Guides on adjusting neutral lockout and tracking for proper mower control.
Details how to position the parking brake handle correctly.
Explains how to adjust the left hand side lockout bolt for proper control lever alignment.
Details the procedure for aligning the ground speed control levers.
Explains how to adjust the right hand side lockout bolt for proper control lever alignment.
States that deck lift rods are fixed and cannot be adjusted.
Provides steps to check if the mower deck requires leveling.
Details the steps for leveling the mower deck for optimal cutting performance.
Describes deck lift assist springs and notes they are not adjustable.
Outlines the procedure for replacing the mower deck drive belt.
Provides detailed steps for replacing the mower deck drive belt, including tensioning.
Details steps for replacing the transaxle drive belt, including tension adjustment.
Explains how to adjust the operator platform suspension for ride comfort.
Details the procedure for adjusting the parking brake.
Provides instructions for cleaning the battery terminals and cable ends.
Explains how to check battery voltage to diagnose charging system issues.
Outlines safety precautions and procedures for charging a discharged battery.
Provides instructions and safety warnings for jump-starting the mower battery.
Lists common problems, their causes, and remedies for the mower unit.
Presents detailed charts for diagnosing and resolving common engine and drive issues.
Addresses streaking issues, their causes, and remedies related to cutting.
Discusses scalping, its causes like deck misadjustment, and solutions.
Explains stepped cutting caused by deck damage or misadjustment and how to fix it.
Lists detailed specifications for different engine options used in the mower models.
Provides specifications for chassis, fuel tank, wheels, transmissions, and speeds.
Details the dimensions of the mower decks, including length, width, height, and weight.
Outlines the limited warranty policy from Briggs & Stratton for the mower and its components.
Details exclusions from warranty coverage related to use, abuse, maintenance, fuel, and other factors.
General| Brand | Ferris |
|---|---|
| Model | SRS Z2 Series |
| Category | Lawn Mower |
| Language | English |
To Next Page