Operation | Machine care | Warranty
Check the carbon brushes regularly (dirty or worn carbon brushes result in excessive
sparking and speed faults).
Always replace the carbon brushes in pairs.
8. MACHINE CARE
Overload
Never use excessive force when cutting. Too much pressure reduces the speed of the machine,
and the required power is greatly reduced. This may result in overload which can damage the
motor of the machine. When the machine becomes too hot, allow it to run for two minutes at
no load and then interrupt working for a short time. Clean the machine with a clean cloth and a
brush. Ensure that the ventilation slots are not blocked.
9. WARRANTY
The Warranty Card shall be valid only when submitted together with the purchase receipt.
Keep the both documents in a safe place. To lodge a warranty complaint, turn to your dealer
or a service centre. The warranty shall apply to all product defects and faults that occurred
during the warranty period and were demonstrably attributable to material or manufacturing
defects. In such cases the product shall be repaired and/or adjusted. The warranty shall not
apply to standard wear of the product, as well as to faults attributable to overloading, using of
inappropriate accessories or improper operation of the product.
17
OPERATING INSTRUCTIONSELECTRICAL JIG SAW
ENDeclaration of conformity
10. DECLARATION OF CONFORMITY
Product/Name: JIG SAW / FIELDMANN
Type/Model: ……………................
230V - 50Hz / 800W / 0-2800rpm / MAX 80mm
The product complies with the following directives:
The Directive of the European Parliament and the Council No. 2006/95/EC dated
12 December 2006 on the harmonisation of the laws of Member States relating to electrical
equipment designed for use within certain voltage limits.
The Directive of the European Parliament and the Council No. 2004/108/EC dated
15 December 2004 on the harmonisation of the laws of the Member States relating to
electromagnetic compatibility and repealing Directive No. 89/336/EEC.
The Directive of the European Parliament and the Council No. 2006/42/EC dated
17 May 2006 on machinery, and amending Directive No. 95/16/EC.
The Directive of the European Parliament and the Council No. 2002/95/EC dated
27 January 2003 on the restriction of the use of certain hazardous substances in electrical
and electronic equipment.
The Directive of the European Parliament and the Council No. 2005/88/EC dated
14 December 2005 amending Directive No. 2000/14/EC on the harmonisation of the laws
of the Member States relating to the noise emission in the environment by equipment for use
outdoors
and standards:
EN 60745-1:2009+A11:2010
EN 60745-2-11:2010
EN 60825-1:2014
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
CE Certification: ............................................................................................................................................... 16
FAST ČR, a.s. is authorised to act on behalf of the manufacturer.
Manufacturer:
FAST ČR, a.s.
Černokostelecká
1621,251 01 Praha , Česká republika
Tax ID:: CZ26726548
In Prague, 23 JAN 2016
Name: Zdeněk Pech
Chairman of Board Signature and stamps:
P
FDP 200805-E
EU DECLARATION OF CONFORMITY
Product / brand: Hand-held Jig Saw / FIELDMANN
Type / model: FDP 200805-E as factory model M1Q-DD20-80
AC 230V, 50Hz, 800W, 0-2800/m
-1
, Class II, IP20, LED light,
Laser Class II
L
PA
= 86dB(A), L
WA
= 97dB(A)
Manufacturer: FAST ČR, a.s.
Černokostelecká 2111, 100 00 Praha 10, Czech Republic
VAT no: CZ26726548
The product is inline with directives and regulations listed below:
Directive MD 2006/42/EC
Directive EMC 2014/30/EU
Directive NEOE 2000/14/EC
Directive RoHS 2011/65/EU
and norms:
EN 62841-1:2015+AC
EN 62841-2-11:2016
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
Place of issuance: Prague Name: Ing. Zdeněk Pech
Chairman of the Board
Date of issuance: 23. 8. 2021
Signature:
To Next Page
Loading...
