page 30
INSTRUCTIONS FOR ASSEMBLY AND USE
The assembly should be performed by qualified personnel only !
Compact rotary actuator for brass mixing valves
EUROMIX MV 120 …
FEATURES
Euromix MV 120 is a compact version of a motor and four way rotating mixing valve. It is designed for use in radiators, floor
or remote heating systems.
- Due to small dimensions is suitable for systems with copper installation
- Dimensions from ” to 1 ”
- Three wire control with two or three point regulators
- Possibility of manual control
- Visible mark of valve shutter position (red pointer on drive cover)
- Quick and simple assembly the actuator on the mixing valve by push/pull system, without screwing
½¼
The motor is not equipped with a connecting cord with plug nor with a switch for disconnecting the
device from the mains ! Therefore the connection should be performed thought a suitable external
switch ! It is also necessary to built-in a fuse in front of the drive to protect it from the current
overloads ! The device should be protected from over voltage shocks ! Before each intervention
the drive should be disconnected from power supply ! By installation must be observed to according to relevant local
standards. The installation must be grounded.
! WARNING !
C13-4606-EUROMIX-v10-ang-504064.cdr
Kvs for type: F3
0,1
1
2
4
6
1
10
20
40
60
80
10 Bar
m/h
3
DN15 - K =4
VS
DN20 - K =7
VS
DN25 - K =10
VS
DN32 - K =15
VS
100
60
50
5
40
30
20
10
10
0
0
80
70
90
valve position
% hot water
FLOW DIAGRAM
Kvs for type: F4
TECHNICAL CHARACTERISTIC
Power supply.....................
Power consumption...........
Rotation angle...................
Rotation time for 90°..........
Max. starting torque.........
Drive protection class........
Electrical protection...........
Ambient temperature.........
Micro switch rating..............
Connection cord................
Controls............................
Reduction gears................
Housing............................
230 V, 50 Hz
3.5 VA
90°
210s
max 8 Nm
IP 44
class II
10 ... 60 °C
5(1)A, 250 VAC
4 x 0.5 mm , L=2000 mm
With three wires SPDT ( )
Steel gears, sintered and milled
Synthetic materials (PA66)
2
Drive unit
WITH FOUR WAY BRASS MIXING VALVE
WITH THREE WAY BRASS MIXING VALVE
125
E
C
D
125
E
C
D
A
B
EUROMIX F4-2
EUROMIX F4-3
EUROMIX F4-4
EUROMIX F4-5
CODE
10055
10056
10057
10058
B
72
72
90
90
D
139
139
146
146
E
72
72
90
90
1,34
1,22
1,97
1,56
DN
15
20
25
32
C
18.5
18.5
24
24
A
1/2"
3/4"
1"
11/4"
K
vs
3,4
6
8,1
10
kg
EUROMIX F3-2
EUROMIX F3-3
EUROMIX F3-4
EUROMIX F3-5
CODE
10051
10052
10053
10054
B
72
72
90
90
D
139
139
146
146
E
54
54
69
69
1,29
1,19
1,10
1,53
DN
15
20
25
32
C
18.5
18.5
24
24
A
1/2"
3/4"
1"
11/4"
K
vs
4
7
10
15
kg
A
B
0,1
1
2
4
6
1
10
20
40
60
80
10 Bar
m/h
3
DN25 - K =8.1
VS
DN32 - K =10
VS
DN20 - K =6
VS
DN15 - K =3.4
VS
To Next Page
Loading...
