Why does my FISCHBEIN Industrial Equipment machine run but not sew?
Your FISCHBEIN Industrial Equipment might run without sewing due to several reasons: it could be out of thread, so fit a new cone; the thread might be broken, in which case you should re-thread the sewing head; the needle could be broken, so replace it; or the drive belt might be loose, so tighten the drive motor belt.
Why does the thread constantly break on my FISCHBEIN Industrial Equipment?
If the thread is constantly breaking on your FISCHBEIN Industrial Equipment, it could be due to several reasons. The thread might be stuck or blocked around the thread tensioners, so check the thread guide or adjustment. The thread tensioners could be maladjusted, so readjust them. The needle or looper might be worn or bent, so replace them. The throat plate might be worn or damaged, so replace it. The needle might be overheating, so try using another type of bag, a needle cooler, or lubricated thread. There might be too much thread tension, so reduce the tension. Finally, the thread might be of poor quality, so use a higher quality thread, such as Fischbein lubricated thread.
Why is the chain stitch quality poor on my FISCHBEIN Industrial Equipment?
A poor quality chain stitch on your FISCHBEIN Industrial Equipment could be due to several factors. The thread might be wrapped around guides or another object, so remove the thread and re-thread the sewing head. There might be poor thread tension, so re-adjust it. The looper, needle, or needle guide might be maladjusted, so re-adjust them. The relationship between the looper and needle might be maladjusted, so re-adjust that as well.
How to fix a poor stitch on FISCHBEIN Industrial Equipment?
If you're experiencing a poor stitch quality on your FISCHBEIN Industrial Equipment, it could be due to a damaged throat plate, so replace it. The presser foot pressure might be incorrect, so adjust the pressure. The feed dog might be worn, so replace it. The thread tension might be poorly adjusted, so adjust the thread tension.
What causes skipped stitches on FISCHBEIN Industrial Equipment?
Skipped stitches on your FISCHBEIN Industrial Equipment can occur if the thread tension is badly adjusted, so adjust the thread tension. Another cause might be the thread pull off being badly adjusted, so adjust it again. Also, using poor quality thread can lead to skipped stitches, so use a higher quality thread, such as Fischbein lubricated thread.
Why does my FISCHBEIN Industrial Equipment have no chain stitch?
If your FISCHBEIN Industrial Equipment is producing no chain stitch, it could be due to a bent or dull needle, so replace the needle. The thread tension might be poor, so check the thread tension. The feed dog or presser foot might be worn out, so replace them.
What causes bags to tear when using FISCHBEIN Industrial Equipment?
If bags are tearing when using your FISCHBEIN Industrial Equipment, it could be due to a damaged throat plate, so replace it. There might be too much pressure on the presser foot, so reduce the pressure. The presser foot might be damaged, so replace it. The stitches might be too close, so reset and check the stitch length.
Why does the sack tear on the sewing line of my FISCHBEIN Industrial Equipment?
If the sack tears on the sewing line of your FISCHBEIN Industrial Equipment, it could be due to too much thread tension, so reduce the tension. The bag might be too thin, so change the bag type. The stitch might be too small, so increase the size of the stitch.
Why does my FISCHBEIN Industrial Equipment make noise and have excessive vibration?
Noise and excessive vibration in your FISCHBEIN Industrial Equipment can be caused by internal components being loose or worn. It can also be caused by sewing head or pulley being loose, so check and tighten screws or tension.
Why is the sewing line wobbly on my FISCHBEIN Industrial Equipment?
A wobbly sewing line on your FISCHBEIN Industrial Equipment could be due to faulty feed or poor synchronization, so check synchronization.
Describes the features and models of Fischbein sewing heads.
Lists critical safety precautions for operating and maintaining the sewing heads.
Details technical specifications like maximum speed, stitch length, and weight.
Step-by-step guide for safely removing the sewing head from its packaging.
Specifies the recommended motor specifications for powering the sewing heads.
Instructions on how to securely attach the sewing head to its support system.
Details the lubrication requirements and warnings for the sewing head's oil system.
Outlines daily and periodic maintenance tasks to ensure optimal performance and longevity.
Provides guidance on safely starting up the sewing head after initial installation or downtime.
Lists recommended consumables like cleaning solvent, oil, and thread.
Detailed steps for threading the needle and looper, including optional filler cord.
Instructions for adjusting looper and needle thread tension for optimal stitch quality.
Guide on how to set and adjust the stitch length for various bag materials.
Procedure for replacing the cork seal located between the housing plates.
Steps for safely removing and installing a new needle in the sewing head.
Instructions for replacing the feed dog component of the sewing head.
How to remove and replace the throat plate on the sewing machine.
Method for adjusting the pressure exerted by the presser foot for sewing.
Comprehensive guide to fine-tuning the sewing head for optimal performance.
Adjusting the tape/thread clipper mechanism on Model 201 sewing heads.
Procedure for replacing the blades on the tape/thread clipper for Model 201.
Instructions for mounting and adjusting the rotary air knife on Model 200.
Explains the uses of the timing gauge for various machine adjustments and measurements.
Covers adjusting sewing head speed and synchronizing it with the production line.
Provides a chart of sewing head RPMs based on conveyor speed and stitch length in English units.
Chart showing sewing head RPMs related to conveyor speed and stitch length in Metric units.
Common causes and solutions when the machine runs but fails to sew.
Identifies causes for needle breakage and provides corresponding solutions.
Addresses issues where bags get stuck in the sewing machine and their resolutions.
Explains why chain stitches might be poorly cut and how to fix it.
Troubleshooting steps for a wobbly sewing line or stitching pattern.
Solutions for tape scuffing issues specific to the Model 201.
Lists specific parts needed for setting up Model 200 sewing heads.
Lists specific parts required for setting up Model 201 sewing heads.
General| Brand | FISCHBEIN |
|---|---|
| Model | Empress Series |
| Category | Sewing Machine |
| Language | English |
To Next Page
