4
4
2
2
1
1
TREASURE HUNTER’S CODE OF ETHICS:
•Always check Federal, State, County and local laws before searching.
•
Respect private property and do not enter private property without the owner’s permission.
•Take care to refill all holes and leave no damage.
•Remove and dispose of any and all trash and litter found.
•
Appreciate and protect our inheritance of natural resources, wildlife and private property.
•Act as an ambassador for the hobby, use thoughtfulness, consideration and courtesy
at all times.
•Never destroy historical or archaeological treasures.
•All treasure hunters may be judged by the example you set; always conduct yourself
with courtesy and consideration of others
5
5
-
-
Y
Y
E
E
A
A
R
R
L
L
I
I
M
M
I
I
T
T
E
E
D
D
W
W
A
A
R
R
R
R
A
A
N
N
T
T
Y
Y
The F4 metal detector is warranted against defects in materials and
workmanship under normal use for five years from the date of purchase to
the original owner.
Damage due to neglect, accidental damage or misuse of this product is not
covered under this warranty. Decisions regarding abuse or misuse of the
detector are made solely at the discretion of the manufacturer.
P
P
r
r
o
o
o
o
f
f
o
o
f
f
P
P
u
u
r
r
c
c
h
h
a
a
s
s
e
e
i
i
s
s
r
r
e
e
q
q
u
u
i
i
r
r
e
e
d
d
t
t
o
o
m
m
a
a
k
k
e
e
a
a
c
c
l
l
a
a
i
i
m
m
u
u
n
n
d
d
e
e
r
r
t
t
h
h
i
i
s
s
w
w
a
a
r
r
r
r
a
a
n
n
t
t
y
y
.
.
Liability under this Warranty is limited to replacing or repairing, at our option,
the metal detector returned, shipping cost prepaid to Fisher Labs. Shipping
cost to Fisher Labs is the responsibility of the consumer.
To return your detector for service, please first contact Fisher Labs for a Return
Authorization (RA) Number. Reference the RA number on your package and
return the detector within 15 days of calling to:
1465-H Henry Brennan Dr.
El Paso, TX 79936
Phone: 915-225-0333 ext.118
Warranty coverage does not include the cost of transporting the detector
back to an owner who is located outside of the United States of America.
NOTE TO CUSTOMERS OUTSIDE THE U.S.A.
This warranty may vary in other countries, check with your distributor for details.
Warranty does not cover shipping costs.
According to FCC part 15.21 Changes or Modifications made to this device not expressly approved by the
party responsible for compliance could void the users authority to operate this equipment.
This device complies with FCC Part 15 Subpart B Section 15.109 Class B.
Copyright© 2013
All rights reserved, including the right to reproduce this book, or parts thereof, in any form.
Fisher
®
is a registered trademark of Fisher Research Labs
www.fisherlab.com
MADE IN USA
ASSEMBLY
●
1 Position detector upright.
●
2 Rotate the LOCKING COLLAR fully in the
counterclockwise direction.
●
3 Insert your finger inside the tube and make sure the
INTERNAL CAM LOCK is flush with the inside of the tube.
●
4
Insert the MIDDLE STEM into the
S-ROD, with the SILVER BUTTON
pointed upward
●
5 Rotate the MIDDLE STEM until the
SILVER BUTTON locates in the hole.
●
6 Twist the LOCKING COLLAR fully in the clockwise
direction until it locks.
●
7 Repeat this process on the LOWER STEM.
●
8 Using the BOLT and KNURLED KNOB, attach
the SEARCHCOIL to the LOWER STEM.
●
9
Adjust the LOWER STEM to a length that lets you
maintain a comfortable upright posture, with your arm
relaxed at your side, and the SEARCHCOIL parallel to the
ground in front of you.
●
10
Wind the CABLE securely around the STEMS.
●
11
Connect CABLE PLUG to housing.
Do not twist the Cable or Plug. Turn Locking Ring only. Use
minimal finger pressure to start the threads. Do not cross-
thread. When the Locking Ring is fully engaged over the
threaded connector, give it a firm turn to make sure that it
is very tight. When the Locking Ring is fully engaged over the
threaded connector, it may not cover all of the threads.
●
12
Tighten both LOCKING COLLARS.
To Next Page
Loading...
