EasyManua.ls Logo

Flin Energy 3kVA-24V - User Manual

Flin Energy 3kVA-24V
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
User Manual
FlinSlim Edge
Solar Hybrid Inverter
With Inbuilt Stabilizer
Version: 1.1

Table of Contents

Questions and Answers

  • B
    Bryan FloydAug 4, 2025
    Why does my Flin Energy 3kVA-24V work in battery mode when mains exist?
    • J
      Jasmine MartinezAug 4, 2025
      If your Flin Energy Inverter continues to operate in battery mode even when mains power is available, the following could be the reasons: * **Tripped Input Protector:** Check if the AC breaker has tripped and ensure the AC wiring is properly connected. * **Poor AC Power Quality:** The AC power from the shore or generator might be insufficient. Verify that the AC wires are not too thin or too long. If using a generator, ensure it is working correctly and that the input voltage range setting is correct. You might also consider changing the output source priority to 'Utility first'.
  • S
    Stacie JohnsonAug 8, 2025
    What to do if my Flin Energy Inverter has no response after power on?
    • B
      Brian MasonAug 8, 2025
      If your Flin Energy Inverter doesn't respond after you power it on, it could be due to the following reasons: * **Low Battery Voltage:** The battery voltage might be too low (below 1.4V/Cell). Check the batteries and wiring to ensure they are well connected and recharge the battery. * **Reversed Battery Polarity:** The battery polarity might be connected in reverse. Replace the battery.
  • T
    Timothy MoralesAug 13, 2025
    Why does my Flin Energy 3kVA-24V Inverter shut down during startup?
    • F
      frederickpadillaAug 13, 2025
      If your Flin Energy Inverter shuts down automatically during the startup process, it is likely due to low battery voltage (less than 1.91V/Cell). To resolve this, try to recharge or replace the battery.
  • A
    alicia98Aug 17, 2025
    Why does the internal relay switch on and off repeatedly on my Flin Energy Inverter?
    • T
      thomas16Aug 17, 2025
      If the internal relay of your Flin Energy Inverter switches on and off repeatedly when you turn it on, the battery might be disconnected. Check the battery wires to ensure they are properly connected.
  • S
    Sandra YangAug 21, 2025
    What to do if Flin Energy 3kVA-24V Inverter has over current or surge?
    • P
      Peter HardingAug 21, 2025
      To address an over current or surge with your Flin Energy Inverter, restart the unit. If the error happens again, please return to repair center.
  • K
    Kathryn GilesAug 26, 2025
    What to do if Flin Energy 3kVA-24V Inverter has internal components failed?
    • P
      pmartinAug 26, 2025
      To address the issue of failed internal components in your Flin Energy Inverter, return to repair center.
  • L
    Leslie HooverOct 30, 2025
    Why is my Flin Energy 3kVA-24V beeping and the red LED is on?
    • T
      Teresa OchoaOct 30, 2025
      If the buzzer on your Flin Energy Inverter is beeping continuously and the red LED is on, it could be due to several reasons: * **Overload:** The inverter might be experiencing an overload (over 110%). Try reducing the load by turning off some equipment. * **Short Circuit:** There might be a short circuit in the output. Check the wiring and remove any abnormal loads. * **Over Temperature:** The internal converter component's temperature may be too high (above 120°C, applicable for 1-3KVA models only). Ensure the unit's airflow isn't blocked and the ambient temperature isn't too high. * **Battery Issues:** The battery might be over-charged or the voltage might be too high. Check the battery specifications and quantity to ensure they meet the requirements. In case of over-charged ba...

Summary

About This Manual

Purpose

Describes the assembly, installation, operation and troubleshooting of this unit.

Scope

Provides safety and installation guidelines as well as information on tools and wiring.

Safety Instructions

Introduction

Features

Lists the key capabilities and functionalities of the inverter/charger.

Basic System Architecture

Illustrates a typical system setup for the inverter/charger.

Product Overview

Installation

Unpacking and Inspection

Guidance on how to unpack the unit and check for damages.

Wall Mounted Installation

Instructions for securely mounting the inverter on a wall surface.

Desktop Installation

Steps to convert the inverter for desktop placement.

Connections

Battery Connection

Procedures and guidelines for connecting the battery to the inverter.

AC Input;Output Connection

Instructions for connecting the inverter to AC power sources.

PV Connection

Steps for connecting photovoltaic (PV) modules to the inverter.

Communication Connection

How to establish communication between the inverter and a PC.

Operation

Power ON;OFF

Procedure for turning the inverter unit on and off.

Operation and Display Panel

Overview of the front panel controls, indicators, and LCD display.

LCD Display Icons and Information

Explanation of symbols, icons, and data shown on the inverter's LCD screen.

LCD Setting and Configuration

Guide to configuring inverter settings through the LCD menu.

Operating Modes and Indicators

Operating Mode Description

Details on various operating modes like Standby, Fault, Line, and Battery.

Fault Reference Codes

List of fault codes and their corresponding error descriptions.

Warning Indicators

Explanation of warning events, audible alarms, and icon indications.

Specifications

Line Mode Specifications

Technical specifications for the inverter operating in line mode.

Inverter Mode Specifications

Technical specifications for the inverter operating in inverter mode.

Charge Mode Specifications

Specifications related to utility and solar charging modes.

General Specifications

Overall specifications including safety certification and temperature ranges.

Troubleshooting

Appendix I: Parallel Function

Introduction to Parallel Function

Overview of parallel operation modes and capabilities for 5K models.

Parallel Kit Package Contents

Lists the components included in the parallel operation kit.

Parallel Board Installation

Step-by-step guide for installing the parallel connection board on 5K models.

Mounting and Wiring for Parallel Units

Guidelines for mounting and wiring multiple inverters in parallel.

Parallel Operation Configuration

Single Phase Parallel Operation

Wiring diagrams and steps for connecting inverters in single-phase parallel.

Three-Phase Equipment Support

Diagrams and procedures for supporting three-phase equipment with multiple inverters.

Advanced Settings and Commissioning

LCD Setting Programs (28 & 30)

Configuration details for AC output mode and PV judge condition.

Commissioning Procedures

Steps for commissioning parallel single-phase and three-phase inverter systems.

Appendix II: Backup Time Table

Flin Energy 3kVA-24V Specifications

General IconGeneral
BrandFlin Energy
Model3kVA-24V
CategoryInverter
LanguageEnglish

Related product manuals