FloPlast AF32 - 1.0 Technical Specification; AF32;AFE32 Valve Details; AV110;AVE100 Valve Details; AF110 Valve Details

3
Addional Informaon
CE Marking
FloPlast has taken the responsibility of CE marking the products in accordance with harmonised European standard BS
EN 12380: 2002 and data is given in FloPlast’s Declaraon of Performance as applicable to the range.
1.0 Technical Specicaon
1.1 AF32/AFE32: The AF32 and AFE32 have been designed for installaon directly onto 32mm UK designated Solvent
Waste Pipe. with the use of the universal adaptor (provided with the product), the AF32 can also to be installed onto
40mm and 50mm UK designated pipe. The valve is also available designated as AFE32, which has been designed for use
with Eurpoean designated 32mm/40mm and 50mm Solvent Waste Pipe.
FloPlast’s AF32 Air Admiance Valve, (as seen on the front cover) comprises of an injecon-moulded, two-part acry-
lonite butadine styrene (ABS) body, screwed together incorporang an EPDM sealing ring. The valve incorporates a slid-
ing ABS injecon moulded disc and EPDM (ethylene propylene diene monomer) seal (poppet), this acts as the opening
and closing seal.
1.2 AV110/AVE100: The AV110 has been designed for installaon directly onto 110mm UK designated pipe. The
AVE100 has been designed for use with European designated 100mm Pipe.
FloPlast’s AVE100/AV110 Air Admiance Valve, (as seen on the front cover) comprises an injecon-moulded, two-part
poly vinyl-chloride (PVC-U) body, screwed together incorporang an EPDM sealing ring. The valve incorporates a sliding
ABS injecon moulded disc and EPDM sealing ring (poppet) which acts as the opening and closing seal.
1.3 AF110: The AF110 has been designed for installaon directly into 110mm UK designated pipe with the use of
and EPDM nned seal. Addionally the AF110 can be installed solvent welded directly onto 82mm UK designated pipe
by removing the nned seal and using the socket on the body. The valve can also be installed directly into 100mm or
110mm European designated pipe with the use of an EPDM nned seal, this product is designated AFE110.
FloPlast’s AF110 Air Admiance Valve, (as seen on the front cover) comprises of an injecon-moulded, two-part poly
vinyl-chloride (PVC-U) body, screwed together incorporang an EPDM sealing ring. The valve incorporates a sliding ABS
injecon moulded disc and EPDM seal (poppet) which acts as the opening and closing seal.
1.4 AX110: The AX110 incorporates the same features as the AF110, with the excepon of the inclusion of an insect/
debris grill manufactured from Polypropylene.
Document H of the Building Regulaons Clause 1.33 states that AAV’s should not be used externally or in dust laden at-
mospheres, however due to the design criteria requirements of the terminaon of SVP’s within 3 metres of an opening
window, and the use of the roof as habital space and also the upturn in lo/roof area conversions, and as a means of
overcoming unsightly SVP installaons, Building Control Ocers are accepng their use.
FloPlast strongly advise that conrmaon of acceptance of the use of the AX110 is gained from Building Control prior to
installaon.
1.5 These valves incorporate spigots detailed in Table 1. They incorporate a nned seal for installaon into 110mm and
100mm pipes or ABS and PVC-U solvent sockets.
1.6 The valves incorporate spigots with diameters that are in accordance with the standards for waste pipe, including:
BS EN 1329-1, BS EN 1455-1, BS EN 1565-1, BS EN 1566-1, BS4514 and BS5255.
1.7 Connuous quality control is exercised during the manufacture and assembly , including visual checks, checks on
dimensional accuracy and 100% funconal tesng of each product. The raw materials and bought-in goods are subject
to quality controls as dened within our ISO9001 Quality Mangement System (FM 501414).
1.8 FloPlast AAV’s are designated A1 in accordance with BS EN 12380: 2002 and can be ed below the ood level of
connected appliances, in air temperatures between -20°C and 60°C.