To Next PageTo Next PageWhat to do if my Flotec Power Pump motor will not run?
If the Flotec Power Pump motor doesn't run, check the following: * **Blown fuse or tripped circuit breaker:** Disconnect the power and replace the fuse or reset the circuit breaker. * **Power cord:** Ensure the power cord is plugged into a 115 Volt grounded outlet.
Why is my Flotec PressureMate FP4815 motor running but no water is delivered?
If the Flotec Power Pump motor runs but no water is delivered, consider these potential issues: * **Improper priming:** Re-prime the pump according to the instructions. * **Clogged water filter:** Stop the pump, shut off the water, and change the filter cartridge. Ensure the filter is installed on the discharge side of the pump. * **Discharge valve closed:** Open the valve. * **Pipe size too small:** Re-pipe using pipe of the same size as the suction and discharge ports on the pump. * **Impeller is plugged:** Clean the impeller. * **Pipes are frozen:** Thaw the pipes.
What to do if my Flotec PressureMate FP4815 Power Pump does not deliver water to full capacity?
If the Flotec Power Pump isn't delivering water to its full capacity, consider these possible causes: * **Corroded pipes:** Replace them with plastic or new steel pipes. * **Piping is too small:** Re-pipe using pipe the same size as the suction and discharge ports on the pump. * **Insufficient water supply:** Enlarge the inlet pipe and check the well pump system. * **Low voltage:** Ensure the outlet provides 115 Volts.
Why does my Flotec Power Pump motor run hot and overload kicks off?
If the Flotec Power Pump motor runs hot and the overload kicks off, or if the motor doesn't run and only hums, check the following: * **Low voltage:** Check the voltage being supplied to the pump. * **Impeller obstruction:** Make sure the impeller moves freely and is not clogged.
Emphasizes reading and following all safety instructions for personal injury prevention.
Provides general safety guidelines for pump installation and operation to prevent injury and damage.
Details electrical safety precautions, grounding, and GFCI requirements to prevent shock.
Covers pump usage, maintenance, and installation advice, including priming and pipe connections.
Provides guidance on selecting a location, preparing the site, and connecting plumbing for the pump.
Explains electrical connection requirements and precautions for safe pump operation.
Describes the functions and features of the automatic pressure controller and its LEDs.
Details how to operate the pump normally and what to expect during its cycle.
Explains the conditions under which the pump automatically stops its operation.
Covers pump operation issues like pressure drop, no flow, and high temperatures, with troubleshooting steps.
Provides safety warnings for servicing and information on motor and pump seal lubrication.
A table listing common pump symptoms, their possible causes, and corrective actions.
Lists available repair parts for the Model FP4815 pump with corresponding part numbers.
Emphasizes reading and following all safety instructions for personal injury prevention.
Provides general safety guidelines for pump installation and operation to prevent injury and damage.
Details electrical safety precautions, grounding, and GFCI requirements to prevent shock.
Covers pump usage, maintenance, and installation advice, including priming and pipe connections.
Provides guidance on selecting a location, preparing the site, and connecting plumbing for the pump.
Explains electrical connection requirements and precautions for safe pump operation.
Describes the functions and features of the automatic pressure controller and its LEDs.
Details how to operate the pump normally and what to expect during its cycle.
Explains the conditions under which the pump automatically stops its operation.
Covers pump operation issues like pressure drop, no flow, and high temperatures, with troubleshooting steps.
Provides safety warnings for servicing and information on motor and pump seal lubrication.
A table listing common pump symptoms, their possible causes, and corrective actions.
Lists available repair parts for the Model FP4815 pump with corresponding part numbers.
General| Max Pressure | 50 PSI |
|---|---|
| Power Source | Electric |
| Voltage | 115/230V |
| Phase | Single |
| Thermal Protection | Yes |
| Housing Material | Cast Iron |
| Impeller Material | Thermoplastic |
| Type | Jet Pump |
| Inlet Size | 1.25 inches |
| Outlet Size | 1 inch |
