Fly Wing UH-1 - Pre-Flight Checks and Takeoff; GPS Mode Unlock and Takeoff; Takeoff Procedure

使用您的PHANTOM 3 Advanced
3. 检查电量
请分别短按一次遥控器和智能飞行电池的电源开关以检查电量。首次使用智能飞行电池，请务必充满电。
短按一次、再长按2秒遥控器电源开关可开启遥控器（重复本操作可关闭遥控器）。
短按一次、再长按2秒智能飞行电池开关可开启智能飞行电池（重复本操作可关闭智能飞行电池）。
●
推荐在平板设备上使用DJI GO App以获得最佳的体验。DJI GO App要求使用iOS 8.0及以上系统和Android 4.1.2及以上系统。
1. 下载 DJI GO App
安装 DJI GO App，请在软件商店或扫描下方二维码下载。
或用移动设备访问以下网址：http://m.dji.net/djigo
2. 观看入门教学视频
扫描二维码观看扫描二维码下载安装
低 高
电量
使用Phantom 3 Advanced 之前，请 在 DJI GO App 或者 DJI 官方网站产品页面完整观看教学视频与下载阅读
《Phantom 3 Advanced 用户手册》，并仔细阅读以下包装内文档：《Phantom 3 Advanced 快速入门指南》、
《Phantom 3 免责声明和安全操作指引》、《Phantom 3 智能飞行电池安全使用指引》和《物品清单》。
4.充电
●
请使用 DJI 官方提供的充电器充电。充电前需将智能飞行电池取出。
●
连接充电器到交流电源（100~240 V，50/60 Hz；如需要请使用电源转换插头）。
●
智能飞行电池、遥控器开启或关闭的状态下均可充电。建议在关闭状态下充电。
●
在关闭状态下充电时，智能飞行电池与遥控器指示灯全部熄灭表示电已充满。
B
A
B
A
取出智能飞行电池
低 高
电量
请在 DJI GO App 或访问DJI官方网站观看。
http://www.dji.com/cn/product/phantom-3/video
www.dji.com
ADVANCED
PHANTOM 3
• o not stop the motor during flight, otherwise the helicopter will crash. nless there are special circumstances
e.g. the helicopter may collide with a crowd, it is necessary to stop the motor urgently to minimie the injury.
• The helicopter will not be able to take off in case of serious low power alarm.
• fter starting the helicopter motor, the blade will rotate at high speed, which is dangerous. The operator shall
keep a certain distance from the helicopter and keep the helicopter away from the crowd, buildings, trees or
other obstructions to avoid collision.
fter landing, please turn off the helicopter power first and then the transmitter.
●  mode unlock  take off take mode󶊅 as an example
󶆊. eady to fly
lease place the helicopter in a flat open outdoor area with user facing the tail.
1󵼾Turn the transmitter motor run
switch to stop position, dial
mode switch to  , and the H1
light is flashing yellow.
󶊅󵼾ove the helicopter to the outdoor open
environment without trees and buildings,
and power on to wait for the  satellite
signal search.
󶊆󵼾fter waiting for a few minutes, the
light changes from flashing yellow to solid
green . The helicopter was positioned
successfully.
󶊇󵼾nlock as shown in the figure and hold
for about 󶊈 seconds until the H1
flight control unit flashes green light.
󶊈󵼾While the green light is flashing, turn
the stop switch to run position , and the
helicopter motor will start the light is
solid green, repeat the unlock procedure
again.
󶊉󵼾When the helicopter rotor head
speed is stable, push the throttle stick
upwards to take off and raise the
helicopter above ground , then release
the throttle stick and you can hover
appropriately.