3. Replace grassbox and lid carefully.
Failure to fit the grassbox and lid correctly will cause poor collection of
grass clippings.
4. MAINTENANCE
DANGER!
Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower [ Fig. P ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
It is very important that you keep your lawnmower clean.Grass clippings
left in any of the air intakes or under the hood could become a potential
fire hazard.
1. Remove grass from under the hood with spanner / scraper tool.
2. Using a soft brush, remove grass clippings from all air intakes.
3. Remove the blade to gain access to the fan and clean with a soft
brush.
4. Wipe over the surface of your lawnmower with a dry cloth.
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Disconnect the product from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Store the mower in a dry, enclosed and frost-free place where it is
protected from damage.
At the End of the Mowing Season:
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly and
carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Carrying your Lawnmower
Ensure the blade is facing away from you.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling collection
centre.
6. TROUBLESHOOTING
DANGER!
Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
Problem Possible Cause Remedy
Mower fails to operate Is the power turned on? v Check the fuse in the plug.
Replace if blown.
Fuse continues to blow? v Immediately disconnect
from the mains electricity
supply and consult your local
approved Service Centre.
Is the correct starting
procedure being followed?
v See
To start the mower
.
Poor flotation Underside of the mower is
dirty.
v Clean the underside of the
hood and the fan blades.
Cutting height is too low. v Raise to a higher height of
cut. See
Adjusting the Cutting
Height
.
If poor flotation persists, contact the local approved Service
Centre.
Poor grass collection Is the grassbox fitted correctly? v Follow the procedure
described in
Poor Flotation
.
Are you mowing in straight
lines?
Are you cutting more than one
third of the grass length?
Do you need to raise the cutting
height?
Excessive Vibration v Replace broken or missing
plastic cutters.
v Check plastic cutters are
fitted correctly.
If vibration persists, immediately disconnect from the mains
electricity supply and consult your local approved Service Centre.
NOTE: For any other malfunctions please contact the FLYMO service depart-
ment. Repairs must only be done by FLYMO service departments or specialist
dealers approved by FLYMO.
7. TECHNICAL DATA
Electric Rotary Lawnmower
Unit Value
9679093-xx
Hover Vac 250
Value
9679659-xx
Hover Vac 260
Value
9679661-xx
Hover Vac 270
Cutting width cm 25 26 27
Speed of rotation cutting
blade
R/min 7000 ± 5 % 7000 ± 5 % 7000 ± 5 %
Cutting height mm 10 – 30 10 – 30 10 – 30
Grass collector capacity l 15 15 15
Power kW 1.4 ± 5 % 1.4 ± 5 % 1.4 ± 5 %
Weight kg 5.87 (EU), 6.5 (UK)
Sound pressure level L
pA
1)
Uncertainty k
pA
dB (A)
89
3.0
89
3.0
89
3.0
Sound power level L
WA
2)
:
measured / guaranteed
Uncertainty k
WA
dB (A)
92 / 94
2.0
93 / 94
1.0
92 / 93
1.0
Hand / arm vibration a
vhw
1)
Uncertainty k
vhw
m/s
2
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
Measuring process complying with:
1)
EN 60335-2-77
2)
RL 2000/14/EC/ S.I. 2001 No.1701
NOTE: The stated vibration emission value has been measured according to
astandardised test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
8. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you for the services
provided.
Husqvarna UK Ltd. grants a warranty for all original FLYMO new products
for two years from the date of original purchase from the retailer, provided
that the devices have been for private use only.
7
11257-85.960.01.indd 711257-85.960.01.indd 7 20.09.21 11:3520.09.21 11:35
To Next Page
Loading...
Need help?
General
