FORM FIT 11300 User Manual

FORM FIT HOOD DEFLECTOR
MAZDA MPV 2000-2003 11300
HARDWARE KIT TOOLS REQUIRED
4 – Plastic Expansion Plugs 1 – Pair of Side Cutters
4 – #6 x ½” Pan Head Sheet Metal Screws 1 – Phillips Screwdriver
2 – Small Bumpons
4 – Large Bumpons
2 – 3M Anti-Abrasion Film Pads
2 – Black ‘E’ clips – already attached to the deflector
INSTALLATION
1. Open the hood. Be sure that the hood is clean and dry inside and out.
2. Install the two (2) small bumpons as shown in Figure #2.
3. Centre the deflector on the hood; determine where the deflector will mount. Using the side cutters, remove and discard the four hood
seal clips that correspond with the holes in the deflector tab.
4. Insert the deflector mounting tab in between the hood and the hood seal.
5. Center the deflector on the hood. Insert an expansion plug through the holes in the hood seal, the deflector and into the holes in the
hood. Be sure that the expansion plugs and deflector are all well seated into the hood then tighten a screw into each expansion plug.
See Figure #1.
6. Underneath each of the ‘E’ clips, fold an anti-abrasion film pad in half over the leading edge of the hood to cover at least ½” (12mm)
underneath the hood.
7. Attach the ‘E’ clips to the hood by gently pulling the deflector wings towards the leading edge of the hood until they slide over and clip
onto the hood edge. It may be necessary to tap on the clips to fully seat them against the hood.
8. Install the four (4) large bumpons as shown in Figure #2. Attention: The bumpons must be installed on the hood, not on the
deflector!!! If the bumpons are installed on the deflector, they will wear through the paint.
9. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the deflector when closing or opening the hood.
CARE INSTRUCTIONS
Clean the deflector with a mild soap and water solution or plastic cleaner only. Do not use chemicals or solvents. Periodically
check to make sure the bumpons are in place and the deflector is secure. Avoid using automatic car washes. Do not pull on the
deflector when opening or closing the hood.
FIGURE #1 – HARDWARE ASSEMBLY FIGURE #2 – BUMPON PLACEMENT
Thank you for purchasing a
form fit hood deflector.
Retain this sheet for care instructions and kit information.
Rev5.031231

FORM FIT 11300 Specifications

General

Brand	FORM FIT
Model	11300
Category	Automobile Accessories
Language	English

Summary

Hardware Kit

Plastic Expansion Plugs

Four plastic expansion plugs included in the hardware kit for installation.

Sheet Metal Screws

Four #6 x 1/2" pan head sheet metal screws for securing the deflector.

Small Bumpons

Two small bump-ons to be installed as per Figure #2.

Large Bumpons

Four large bump-ons to be installed on the hood, not the deflector.

Anti-Abrasion Film Pads

Two 3M anti-abrasion film pads for protecting the hood paint.

Black 'E' Clips

Two black 'E' clips, already attached to the deflector, for securing it.

Tools Required

Side Cutters

A pair of side cutters is required for installation, likely for removing clips.

Phillips Screwdriver

A Phillips screwdriver is needed for tightening screws during installation.

Installation Instructions

Preparation and Initial Mounting

Clean hood, install small bumpons, center deflector, remove seal clips.

Deflector Attachment and Securing

Insert mounting tab, center deflector, use expansion plugs and screws.

Anti-Abrasion Film and Clip Installation

Apply anti-abrasion film under 'E' clips and attach clips to the hood edge.

Final Bump-on Installation and Adjustment

Install large bumpons on hood, adjust bumpers/latch if needed for clearance.

Important Notes

Ensure bumpons are on hood, not deflector. Do not pull deflector when closing hood.

Care Instructions

Cleaning Recommendations

Clean with mild soap/water or plastic cleaner only; avoid chemicals/solvents.

Maintenance Checks

Periodically check bumpons and deflector security. Avoid automatic car washes.