RETURN
CAMERA ID
FOXEER
A B C D E F G H I J K L M N O P Q
R S T U V W X Y Z
- ! ” # $ % & ( ) _ ˋ , ￥ : ; <=> ? @
\ ˆ﹡﹣×＋／
←→↑↓ CLR POS
00 : 00 00 : 0
WARNING: Read the ENTIRE instruction
manual to become familiar with the
features of the product before operating.
Failure to operate the product correctly
can result in damage to the product,
personal property and cause serious
injury.
NOTICE: This product is only intended for
use with unmanned, hobby- grade,
remote-controlled vehicles and aircraft.
FOXEER disclaims all liability outside of
the intended purpose and will not
provide warranty service related thereto.
SUPPORT: Visit www.foxeer.com/ to get
more information.
MENU: Push MENU(center button) to go to
the main menu.
UP/DOWN: Move up and down through the
menu.
Left/Right: Modify the menu parameters.
Main MENU
SETUP MENU
CAMERA ID
EXIT
PICT ADJUST
DAY / NIGHT
LANGUAGE
CAMERA RESET
ENGLISH
AUTO
YES
ON
Camera ID: ON/OFF. You can setup pilot
name and position.
1. Camera ID
To connect the camera directly to the video
transmitter, plug the 3 pin wiring harness from
the video transmitter into the camera leaving
the OSD pin open.
CAMERA-VIDEO
TRANSMITTER CONNECTION
1. TIME: ON/OFF
2. POWER: ON/OFF
4. V CAL: Voltage calibration, range -0.5~0.5.
6. N/P: NTSC/PAL switchable.
7. SIZE: 4:3/16:9 switchable.
8. CROSSHAIRS: ON/OFF
5. MODE: DAY/ NIGHT/ LED/ B&W.
9. VER: FOXEER_V5.0.
3. VOL ALARM:
You can setup a bat
boundary
(single), click LEFT/RIGHT button to decrease/
increase the value, 3.6V default.
Press top button for 3s, you can access OSD
menu.
FPV OSD Setup
DISPLAY
TIME
EXIT
POWER
VOL ALARM 3.6
V CAL 0.0
MODE DAY
N/P PAL
SIZE
CROSSHAIRS
VER: FOXEER_V5.0
4:3
ON
ON
OFF
CAUTION: If you are using ESC’s with active
braking, we recommend powering the
camera system through a BEC or voltage
regulator.
CAMERA-OSD SWITCH
CONNECTION
Camera Back OSD Switch Front
VBAT+
1. FLIP:
OFF/ H-FLIP/ V-FLIP/ HV-FLIP
2. BRIGHTNESS
3. CONTRAST
4. SHARPNESS
5. HUE
6. COLOR GAIN
2. PICT ADJUST
PICT ADJUST
FLIP
COLOR GAIN
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
160
136
090
136
OFF
122
RETURN
7 Languages: ENGLISH/ DEUTSCH/ FRANCAIS/
PYCCKNN/ PORTUGUES/ ESPANOL/ 中文 .
4. LANGUAGE
DAY/NIGHT include "AUTO" and "MANUAL" ,
click "MANUAL" , you can setup permanent
"COLOR" or "B/W" .
3. DAY/NIGHT
5. Camera reset
Save All: Save all setup.
cancel: Cancel Setup.
Not Save: Can save the value temporary, but
once power o, the value won't save.
6. EXIT
DAY/NIGHT
DAY/NIGHT COLOR
RETURN
Quick switch: At standby status, long press the right
button on OSD board, it can fast change the MODE,
the current mode will show once at the TIMER place.
PREDATOR 5
VBAT+
Mini / Micro
Nano
To Next Page
Need help?
General
