Foxfury Lighting Solutions RUGO User Manual

POWER PACK LIFE
MODE DURATION LUMENS
HIGH 1 hr 700
MEDIUM 1.5 hrs 400
LOW 3.5 hrs 200
DIM 6.75 hrs 70
*Power Pack life may vary according to age and ambient conditions.
The Charge Indicator will turn green
once fully charged.
Charging time is about 2.5 hours.
Do NOT leave Power Pack charging
for extended periods of time.
When disassembled, keep both ends
dry and away from water.
RUGO
™
QUICK START GUIDE
FULL ASSEMBLY CHARGING THE POWER PACK
DISASSEMBLED LIGHT HEAD
DISASSEMBLED POWER PACK
TRI-LENS
™
THUMBSCREWS
POWER/MODE
SWITCH
¼”-20 MOUNT
CHARGE
INDICATOR
LED CONTACT
CAVITY (2)
O-RING
ACCESS SCREW
LED MODULE
SCREW HOLE (4)
1
2
3
Press and hold the Power Pack Release
Lever located on the Light Head portion of
the Rugo
™
.
(Rugo
™
in steps 1–3 shown with no mounts and is flipped to
show Power Pack Release Lever)
While maintaining pressure on the Power
Pack Release Lever, pull the Light Head
and Power Pack apart. If unable to pull
apart easily, try moving the Power Pack
back and forth while continuing to pull.
Insert the provided Micro USB Cable into
the Power Pack. Then, insert the opposite
end USB (Type A) into a USB compatible
power source or into the included AC/DC
Adaptor.
WARNINGS
When used for extended periods of time the
Rugo
™
will become HOT to the touch.
Do not stare into the LEDs for long periods of
time or from a close range (less than 2ft).
This product is designed as an auxiliary lighting
tool to be used with photo, video, and film.
DO NOT use the Rugo
™
as a primary light source
for activities.
While using any FoxFury product, please operate
at safe speeds.
Be sure to rinse the Rugo
™
with fresh water
immediately after use in the ocean or a pool.
It is the responsibility of drone/UAV users to
follow the FAA laws and regulations and/or the
laws and regulations applicable to flight location.
IMPORTANT!
Please fully charge the Quick Swap
™
Power Pack
before using the Rugo
™
for the first time.
!
!
!
!
!
!
POWER CONTACTS
USB CHARGE PORT
LOCKING POST
MOUNTS INCLUDED
THUMBSCREWS (2)
FOR MORE INFO VISIT
FOXFURY.COM/RUGO
OPERATIONAL MODES
DIM mode: Press the Power/Mode
Switch once.
LOW mode: From DIM mode, press
the Power/Mode Switch once.
MEDIUM mode: From LOW mode,
press the Power/Mode Switch once.
HIGH mode: From MEDIUM mode,
press and hold the Power/Mode
Switch once.
OFF: From ANY mode, press and
hold the Power/Mode Switch for
2 sec.
6/2017
¼"–20 AND
COLD-SHOE MOUNT
STANDARD MOUNT
WITH (2) KNOBS

Foxfury Lighting Solutions RUGO Specifications

General

Water Resistance	Yes
Waterproof	Yes
Impact Resistant	Yes
Material	Polycarbonate
IP Rating	IPX7
Power Source	Rechargeable battery

Summary

Full Assembly Components

Power/Mode Switch

The switch used to control power and cycling through operational modes.

Charge Indicator

An indicator light showing the charging status of the power pack.

Thumbscrews

Fasteners used for securing mounts or assembly.

Tri-Lens

The lens system providing different beam patterns.

Safety Warnings

Charging the Power Pack

Disassembling for Charging

Procedure to separate the light head from the power pack for charging.

Charging Procedure

Connecting the power pack to a power source via USB for charging.

Operational Modes

Mode Activation

Instructions for switching between DIM, LOW, MEDIUM, HIGH, and OFF modes.

Power Pack Life

Details on runtime and lumens for each operational mode.

Disassembled Components

Light Head Components

Details on LED contact cavity, LED module, screw holes, and O-ring.

Power Pack Components

Details on locking post, USB charge port, and power contacts.

Included Mounts

Standard Mount

The standard mount with two knobs for attachment.

1/4"-20 and Cold-Shoe Mount

Mounting options for tripods, cameras, or other accessories.

Using the Tri-Lens

Beam Patterns

Description of Flood (120°), Area (55°), and Spot (18°) beam patterns and their uses.

Mounting Instructions

Changing Standard Mount

Step-by-step guide to removing and changing the standard mount.

Changing 1/4"-20 & Cold-Shoe Mount

Step-by-step guide to removing and changing the 1/4"-20 and cold-shoe mount.

Mounting to Devices

Instructions for attaching the Rugo to action cameras, DSLRs, tripods, or puck adaptors.