Airplane Pushrod Size
ī īī§ī²īī²īīīÆīīµīØīīÆīī·īīīīØī»ī»īÆīīīØī»ī»īīīµīÆīīīÆīīīī
īīīī¤
īīīīīīī
īīīīīī¤īī³ī
īīīī
īīīīī
īīīīī¤īīīī¤
īīīīī
īīīīīīī¤
īīīīīīīī
īīīī¤īīīī¤
īīīīīīīīīīīī
īīīīīīīīī¤
īī²īīīÆīÆīīīīīīīÆīī»īØī¬īÆīīīÆīīīī
īīī¼īÆīØīīÆīīīīī¬īµīØīīÆī
īīīīīīīīī¤
īīīÆīÆīī·īī“ī
īīīīīīī¤
īīÆīīīīī
īīī
īīīī¤
īīÆī²īÆīī
īīīīīīīī¤
īīīīīµīÆī
īīīīī¤īīīīīīī¤
ī²īī¼ī»īīī·īī“ī
ī īīīīīīīī
ī
Flap pushrod size
ī¬ī£ī¢ī¢ī
īī¶ī°īī¬ī§īīīīīī£īī²īīīī³īī¤īī„īīÆīī£ī£ī
Aileron push rod size
īīīīī ī¬ī¬īī¢ī¢īīīīīīī¾ī
īī¶ī°īīÆīīīīīī£īī²īīīī“īī¤īī„īīÆīī£ī£ī
Elevator push rod size
īīī īīī°ī°ī¢ī¢
ī
īīæī¦
īī¶ī°īī¬ī§īīīīīī£īī²īīīīµīī¤īī„īīÆīī£ī£ī
Rudder pushrod size
īīīīīī ī°ī©īī¢ī¢īīī
ī
īīī
1
īī¶ī°īīÆīīīīīī£īī²īīīīµīī¤īī„īīÆīī£ī£ī
Air-b
rake Installation
Step4
T-45 Goshawk
ī īī±īīī¢ī
īīīīī”īīīī
ī§ī±īīī¹ī
īīī¢ī
īīī īī”īīīīī§īīī
īīæī
īī
3 3
3 3
ī¶īæ
īī
1.Put the"Screw(B)"into the"Ball head(A)",
then insert "Screw(B)"into the hole of the
"Control horn(D)" and lock it into place using
"Nut(C)"
1.
Thread the "Ball head clevis (B)"onto the
threaded end of "Pushrod (A)". Twist left or right
to increase or reduce the length of the pushrod.
2.
Feed the angled side of the push rod into the
servo arm. Then place the second part of
"Plastic lock(C)" over the "Push rod (A)" and
snap the "Plastic lock(C)" to the push rod to
lock the pushrod in place.
Flap push rod mounting hole
ī
ī
īī
īī
ī·īīæī±ī±ī
īøī¹
ī
īīīīī
ī
īŗ
ī
īīīīīīīīīīīīīīīī ī”ī¢īī”ī£īī”ī¤ī
ī„
īī¦ī²
ī„
īīæ
īī
ī
īī
īī
Aileron push rod mounting hole
īī
īīī
ī
īīīīīīīīīīīīīī
ī
īīīīīīī
īīīīīīīīīīīī»
ī
ī¼
ī½
ī³ī„
ī”
ī„
ī”
ī„
ī”
ī§īØī©īØī©īŖī©īŖī©ī«ī©ī«īØī©īØī©īŖī©īŖī©ī“ī„īīæ
ļæ½ !
ī
ī¤
īī ī ī”ī¢ī£ī£īī¤
īī¤
Elevator push rod mounting hole
ī
ī
īī
īī
r ī
īī¹
ī
ī
īīīī
ī
īīīī¾
ī
īīīī¬īī
ī©īŖī©
ī
īŖ
īī
ī©
ī
ī«
īī®
ī©
īīÆ
ī©
ī”ī°
ī©
ī„
īŖ
ī¦īµ
ī„
īīæ
īī
ī
īī
īī
Rudder pushrod mounting hole
Step 2
Accessories
A
-
Air-brake mount
B
-
Air-brake pin
C
-
E-clip (01.5mm)
D
-
Air-brake
E
-
Servo
(9g
-MG
)
Step 3
1.
Follow Step 1 to assemble the air-brake.
2.
Use glue to attach the servo.
3.
Use glue to attach the air-brake to the fuselage.
4.
Use the push rod to connect the air-brake to the servo
arm. Set up the open angle of the air brake by adjusting
the pushrod length.
(After setup, pay attention when cycling the air-brake. If
the servo makes a buzzing sound, increase the open
angle until it cycles silently.)
Air-brake push rod size
Air-brake push rod installation hole
īīī®ī±ī£ī£īī
īī„īī±ī«īīī¦ī
ī¤īīī¶īīī®īī®ī¹ī©īæī°īī°īīīī½īīīīīæīæī
-6-
To Next Page