To Next PageTo Next PageWhy is my Frigidaire Ice Maker not turning on; indicator lights are off?
If the indicator lights on your Frigidaire Ice Maker display are not illuminated, it indicates a power issue. The cause may be a blown fuse or lack of power. Replace the fuse or turn the power on.
What to do if the water shortage indicator light is on in my Frigidaire Ice Maker?
If the water shortage indicator light is illuminated on your Frigidaire Ice Maker, it could be due to a couple of reasons: either there's no water in the unit, or the pump is full of air. To resolve this: * Add water until it reaches the MAX position. * Press the POWER button to restart the ice maker.
What to do if all indicators twinkle simultaneously on Frigidaire 058465808303?
If all the indicators on your Frigidaire Ice Maker are twinkling at the same time, it means that the water tray is blocked by an ice cube. To fix this, unplug the power, remove the ice blocking the tray, plug the power back in, and press the POWER button. The machine should restart after 3 minutes.
Why is my Frigidaire 058465808303 Ice Maker making ice that is too large and sticking together?
If your Frigidaire Ice Maker is producing ice that's too large and sticking together, it's likely due to ice from previous cycles being left in the water tray. To resolve this, remove the ice while the machine is in standby mode.
Why is my Frigidaire 058465808303 compressor making a buzzing noise?
If the compressor in your Frigidaire Ice Maker is operating abnormally and producing a buzzing noise, it's likely that the voltage is lower than recommended. Stop using the ice maker and do not restart it until the voltage returns to normal.
Why is my Frigidaire 058465808303 working, but the water is warming up?
If your Frigidaire Ice Maker is running, but the water inside is getting warm, it suggests that the solenoid has broken down. The solution is to replace the solenoid valve.
Add water to the reservoir, ensuring it does not exceed the MAX line.
Plug in the unit and press the power button to initiate ice production.
Add water to the reservoir, ensuring it does not exceed the MAX line.
Plug in the unit and press the power button to initiate ice production.
This document provides a comprehensive guide for the Frigidaire Ice Maker, detailing its functions, operational procedures, and maintenance requirements to ensure safe and efficient use.
The Frigidaire Ice Maker is a compact and efficient appliance designed for quick ice production in household and similar settings. Its primary function is to convert water into bullet-shaped ice cubes. The device is equipped with a control panel that provides visual feedback on its operational status, including indicators for "ICE FULL," "ADD WATER," and "ICE MAKING." The "ICE MAKING" indicator flashes when the machine is in deicing mode and remains steadily lit during ice production. The "ICE FULL" indicator flashes when the ice storage container reaches its maximum capacity, prompting the user to remove ice. The "ADD WATER" indicator turns red to signal a water shortage in the reservoir, requiring the user to refill the water tank and restart the machine. This ice maker is not designed for long-term ice storage; users are advised to remove all ice cubes and drain the water after each use, as it does not keep ice frozen.
Operating the Frigidaire Ice Maker involves a few straightforward steps. Before initial use, it is crucial to position the appliance on a level surface, ensuring at least 150mm of clearance from walls and other objects to allow for proper heat dissipation. The transparent lid should be left open for at least two hours prior to the first operation. The manufacturer recommends using spring water, as distilled water is not suitable for this unit.
To begin ice production, the user first opens the lid, removes the ice basket, and adds water to the reservoir. A "MAX" scale within the reservoir indicates the maximum water level, which should not be exceeded. Overfilling requires draining the excess water through the bottom drain plug. Once water is added, the appliance is plugged in, and the power button is pressed to initiate the ice-making cycle. The "ICE MAKING" indicator will illuminate, and the machine will automatically start producing ice. Each cycle produces 9 bullet-shaped ice cubes in approximately eight minutes.
The ice maker features an automatic deicing function that activates after each ice-making cycle, followed by an ice shoveling function. When the ice basket is full, the "ICE FULL" light flashes, and the machine pauses operation. Users should promptly remove the ice to prevent overflow and allow the machine to resume production once the ice level falls below the full sensor.
For optimal performance, the type of ice (small or large) can be selected based on the ambient temperature. Small ice is recommended when the indoor temperature is below 15 degrees Celsius, while large ice is suggested for temperatures above 30 degrees Celsius. It's important to note that during the first three cycles, the ice produced may be small and irregular. If the ice shovel cannot remove ice to the basket, users should gently push the shovel with a finger and press the power button to restart.
In case of a power failure or if the power button is pressed off during an ice-making cycle, small ice chips may form and jam the automatic shovel. To resolve this, the power cord should be disconnected, the shovel gently pushed to the rear of the cabinet, and the ice chips removed before restarting the machine. If the water tray is blocked by an ice cube, unplugging the power, removing the obstruction, and then plugging in and pressing the power button will restart the machine after a 3-minute delay.
Regular cleaning and maintenance are essential for the longevity and hygienic operation of the Frigidaire Ice Maker. The inner liner, ice collecting tray, water box, ice shovel, and evaporator should be cleaned frequently. Before cleaning, the unit must be unplugged, and all ice cubes removed. A diluted solution of water and vinegar is recommended for cleaning both the inside and outside surfaces of the ice maker. It is crucial to avoid spraying the ice maker with chemicals or diluted agents such as acids, gasoline, or oil. After cleaning, the unit should be thoroughly rinsed before being put back into operation.
To ensure proper ventilation, the appliance's ventilation openings, or those in a built-in structure, must be kept clear of obstructions. Mechanical devices or other means to accelerate the defrosting process should not be used, unless specifically recommended by the manufacturer.
For optimal ice quality, the water in the reservoir should be changed at least once a day. If the ice maker will not be used for an extended period, the water should be drained, and the unit cleaned. When reusing the machine after a period of inactivity, it may not have enough water to pump, causing the "ADD WATER" indicator to light up. In such cases, refilling the water and pressing the power button will restart the ice maker.
It is normal for the compressor and condenser surfaces to reach temperatures between 70°C and 90°C during operation, and surrounding areas may become very hot. Due to the fast freezing process, ice cubes may sometimes appear "Cloudy," which is caused by trapped air in the water and does not affect the quality or taste of the ice.
The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the safe use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance. The ice maker should never be immersed in water.
In case of a damaged power cord, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to prevent hazards. If the solenoid breaks down, it should be replaced. If the ice full sensor is damaged, or if the machine is making ice indoors and the "ICE FULL" icon is not displayed when the ice basket is full, the ice full sensor may need replacement, or the service hotline should be contacted.
General| Brand | Frigidaire |
|---|---|
| Model | 058465808303 |
| Category | Ice Maker |
| Language | English |
