SETTING OVEN CONTROLS
SETTING THE SABBATH FEATURE (foruseon
theJewishSabbath & Holidays)
The BAKE TIME and DELAY START pads are used to
settheSabbath feature.The Sabbathfeaturemay onlybe
used withthe BAKE pad. The oven temperaturemay be
sethigheror loweraftersettingthe Sabbath feature(the
oven temperatureadjustmentfeatureshouldbe used only
during Jewish Holidays), however the displaywill not visibly
show or provide any audible tones indicating whether the
change occurred correctly, Once the oven is properly set
using Bake with the Sabbath feature active, the oven will
remain continuously ON until cancelled. This will override
the factory preset 6-Hour Energy Saving feature.
If the oven light will be needed during the Sabbath, press
OVEN LIGHT _ beforeactivatingthe Sabbath feature.
Once the oven lightisturnedON and the Sabbathfeature
isactive,the oven lightwillremain ON untilthe Sabbath
featureisturned OFF. Ifthe oven lightneeds to be OFF,
be sure to turn the oven lightOFF beforeactivatingthe
Sabbath feature.
To Program the Oven to Begin Baking Immediately &
activatethe Sabbath feature (example:bakingat350°F)
1.Be surethattheclockissetwiththecorrecttimeofday.
2.Placethe food intheoven.
3.PressBAKE. _'350°"appearsinthe display.
4.PressSTART. The actualoven temperatureappears in
the display.
5.1fyou desiretosetthe oven controlfora Bake Time or
Delayed Bake Time do so atthistime.Ifnot,skipthis
stepand continueto step7.Refertothe Bake Time I
Delay Startsectionforcompleteinstructions.Remember
theovenwillshutdown afterusingBake Time orDelay
Start and thereforemay onlybe used once duringthe
Sabbath/JewishHolidays.
6.The oven willturnON and beginheating.
7.Pressand holdboththeBAKE TIME and DELAY START
pads for at least 3 seconds. "SAb" will appear in the
display. Once_'SAb" appears inthe display the oven control
will no longer beep or display any further changes and
the oven is properly set for the Sabbath feature.
8.The oven may be turned OFF at any time by first pressing
CANCEL pad (this will turn the oven OFF only). To turn
OFF the Sabbath feature press and hold both the BAKE
TIME and DELAY START pads forat least3 seconds.
"SAb" will disappear from the display.
IHPORTANT
It is not advised to attempt to activate any other program
feature other than BAKE while the Sabbath feature is
active. ONLY the following key pads will function after
setting the Sabbath feature; 0 to 9, BAKE, START &
CANCEL. All other keypads should not be used once
the Sabbath feature is properly activated.
NOTE
"Youmay change the oven temperature once baking has
started by pressing BAKE, the numeric key pads for the
temperature you want (example for 425°C press 4 2 5)
and then pressing START twice (for Jewish Holidays
only). Remember that the oven control will no longer
beep or display any further changes once the oven
issetforthe Sabbathfeature.
Should you experience a power failure or interruption, the
oven will shut off. When power is returned, "SF" (Sabbath
Failure) will be shown in the oven display and the cooktop
displays (models B &C). The oven and cooktop will not turn
back on automatically. If your food was nearly fully cooked,
you may allow the trapped heat in the oven to finish the
cooking process. Otherwise, you should remove the food
when the power failure occurs, because you may only start
the oven once during the Sabbath/Jewish Holidays. After the
Sabbath observance, turn OFF the Sabbath feature and be
sure that all the control knobs are at the OFF position. The
appliance may be used again with all normal functions.
After the Sabbath observance turn OFFthe Sabbath feature.
Press and hold both the BAKE TIM E and DELAY pads for at
least 3 seconds. "SAb" will disappear from the display and
the oven may be used with all normal functions. For further
assistance, guidelines for proper usage, and a complete list
of models with the Sabbath feature, please visit the web at
http: \ \www.sta r-k.org.
How the Electronic Surface Element Controls
work when the Sabbath feature is ON,
(model B & C only)
When your Oven Sabbath feature is ON, the Electronic
Surface Elements are also in Sabbath mode. This means
that all electronic surface element control displays show
"Sb" The surface elements can be used even if the Sabbath
Feature is on.
To turn ON a Surface Element when the Oven Sabbath
Feature is active:
If you turn on a surface element when the oven Sabbath
feature is on, the electronic surface element control will record
that request and execute it with a 15-30 seconds delay. So
the element will start heating 15-30 seconds after the surface
element control was turned on. As the oven control, the
surface element display will not show the setting because
"Sb" is on in the displays. When necessary, it is possible to
adjust the power of the surface element but you have to
remember that the surface element control will adjust the
temperature with the same delay.
To turn OFF the Surface Element when the Oven
Sabbath Mode is active:
To shut off the surface element while the Sabbath feature
is ON, proceed as usual but take note that the element will
immediately turn off without any delay.
31
To Next Page
Loading...
