Fujikura FSM-20PMII User Manual

93 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image









 































 

  

 















 







 II











 

 













Table of Contents

Questions and Answers:

P
Patrick PerezAug 7, 2025
How to fix 'OVER RUN XF XR YF YR' error on Fujikura Power Tool?
- S
  Sarah LongAug 7, 2025
  If your Fujikura Power Tool displays an 'OVER RUN XF XR YF YR' error, it could be due to a few reasons. First, check if there's dust on the V-groove and clean it according to section 8.1.1. Another cause might be that the fiber has detached from the V-groove; if so, carefully place the fiber back into the V-groove. Lastly, ensure that the fiber's primary coating is completely removed. If not, cleave the fiber again and repeat the entire splicing procedure.
P
Phillip JohnsonAug 14, 2025
What to do if Fujikura Power Tool shows 'OVER RUN PLF PLR PRF PRR' error?
- J
  Joshua McintoshAug 15, 2025
  If your Fujikura Power Tool shows the error 'OVER RUN PLF PLR PRF PRR', it indicates that the axis is moving to its forward or backward limit. To resolve this, first, ensure the fiber is correctly placed on the V-groove. Next, clean the mirrors and objective lens. Finally, verify that the fiber itself is clean.
A
Anthony ThompsonAug 21, 2025
Why Fujikura Power Tool displays 'OVER RUN FOCUS NEAR FOCUS FAR FIELD UP FIELD DOWN'?
- S
  Suzanne CarterAug 21, 2025
  If you're seeing 'OVER RUN FOCUS NEAR FOCUS FAR FIELD UP FIELD DOWN' on your Fujikura Power Tool, the fiber might not be properly set before automatic splicing. Try placing the fiber again on the V-groove to ensure correct positioning.
N
Nicole CollinsAug 29, 2025
What to do if Fujikura Power Tool displays 'OVER RUN ZLF ZLR' error?
- C
  cindyjohnsonAug 29, 2025
  The 'OVER RUN ZLF ZLR' error on your Fujikura Power Tool can occur if the fiber is cleaved too short. Ensure the fiber is cleaved to its proper length. Also, check if the fiber is detached from the V-groove and, if so, place it back into the V-groove.

Fujikura FSM-20PMII Specifications

General

Brand	Fujikura
Model	FSM-20PMII
Category	Power Tool
Language	English

Summary

General Information

Construction Overview

Splicer Components

Details the standard components included with the FSM-20PMII splicer.

Optional and Other Accessories

Lists optional and other accessories available for the FSM-20PMII.

Input Power Requirements

Specifies the acceptable input voltage and frequency range for the splicer.

Product Description

Main Body Components and Views

Describes the front, top, and side views of the FSM-20PMII main body.

Control Box Functions

Details the functions and layout of the FSM-20PMII control box.

Fiber Guide Function

Explains the function and use of the fiber guide accessory.

Operation Guide

Splicing Procedure

Step-by-step guide for connecting power cords and powering on/off the splicer.

Splice Mode Alignment Procedures

Details alignment processes for different splice modes (P1, P2, P3, SM, MM).

Menu Commands and Settings

Optional Function and Parameter Settings

Covers optional function settings, arc parameters, and PMALIN adjustments.

Option Set Settings

Describes how to configure various option settings for the splicer.

Manual Motor Operation and Monitor Release

Guide for manual motor operation and instructions for detaching the LCD monitor.

Dip Switch Functions

Dip Switch Settings Overview

Details the functions of the five dip switches on the splicer.

Maintenance Mode Operations

Covers entering maintenance mode and its sub-functions like XY RESET and Stuff Measure.

Other Features and Options

Side Mounted Tray and Bar Clamp Options

Details the attachment and use of side mounted tray and bar clamp options.

ARC Power and ECF Adjustments

Guides for adjusting ARC power and using the ECF function for fiber splicing.

Fiber Clamp Strength Adjustment

Instructions for adjusting fiber clamp strength for different fiber diameters.

Maintenance Procedures

Cleaning Guide for Components

Procedures for cleaning the V-groove, objective lens, mirrors, and clamps.

Replacement of Expendable Items

Covers replacement of V-grooves, clamps, electrodes, fuses, and mirrors.

Troubleshooting

Motor Over Run Error Handling

Identifies causes and remedies for motor over run alarm messages.

Error Message Reference

Lists common error messages, their reasons, and suggested remedies.

Guarantee and Contact Information

Product Guarantee Details

Outlines the guarantee period, limits, and required information for repairs.

Contact Addresses

Provides contact information for Fujikura sales and support.

Safe Operation Warnings and Cautions

Alert Symbol Meanings

Explains the meaning of warning, caution, and mandatory symbols in the manual.

Critical Safety Warnings

Lists essential safety warnings concerning operation, power, environment, and electrical hazards.

Handling and Equipment Cautions

Provides cautions on transportation, fiber setting, electrode replacement, cleaning, and equipment handling.

Related product manuals

Preview: Fujikura FSM-100M

Fujikura FSM-100M

Fujikura FSM-100P

Preview: Fujikura 70R+