FUTABA 16SZ - Page 77

78
＜ Linkagemenu ＞
System Type selection
7KH76=LVIRU*+]RQO\7KHV\VWHP
FDQEHFKDQJHGIURPDPRQJFKRLFHV)$667HVW
&+)$667HVW&+)$66708/7,)$667
&+7)+666)+66,WLV)$667HVW&+DQG
)$667HVW&+ZKLFKFDQEHFKRVHQE\56%
VHW7KHPHWKRGRIVHOHFWLRQLVRQWKHQH[WSDJH
*If you change the System type, other model data is not reset.
*After any change, remember to test the model and fully
check servo direction and motion.
$QDORJVHUYRVFDQQRWEHXVHGZLWKWKH56%LQWKH
)$667HVW&+PRGH
Systemtype
6\VWHPPRGHVHWWLQJ5HFHLYHUOLQN
Receiver linking
7KHUHFHLYHUZLOORQO\EHFRQWUROOHGZLWKRXW
EHLQJDIIHFWHGE\RWKHUWUDQVPLWWHUVE\WKH
transmitter it is linked to. When using a receiver
other than one purchased as a set, linking is
necessary.
Moreover, a re-link is required when a new
model is added by model selection, and at the time
of system type change.
Dual receiver function (only FASSTest 18CH )
'XDOUHFHLYHUVFDQEHOLQNHGZLWKWKH76=
Two receivers are recognized individually by ID
QXPEHUV)RUH[DPSOHLQ56%&+RXWSXW
setting function is used, by setting the first as as
&+DQGVHWWLQJWKHVHFRQGDV&+
Two sets of receivers can be used as a set in the
PRGHODOORZLQJ\RXFKDQQHOV6HSDUDWHIDLOVDIH
voltage can be set to each receiver.
+RZHYHUWHOHPHWU\FDQQRWEHXVHGIRUWKHQG
receiver.
Battery fail-safe voltage setup (FASSTest /
T-FHSS mode only)
The voltage at which battery fail-safe activates
FDQEHVHWZKHQ\RXOLQN97KHUHFHLYHU
memorizes the setting as it was at link.
Since power consumption varies with battery
type, servos and condition, please select the fail-
safe activation voltage for your own model.
ŏ6HOHFW>6\VWHPW\SH@LQWKH/LQNDJHPHQX
DQGDFFHVVWKHVHWXSVFUHHQVKRZQEHORZ
P.41
Linking method
&DVHVZKHQOLQNLQJLVQHFHVVDU\
・
:KHQXVLQJDUHFHLYHURWKHUWKDQWKHLQLWLDOVHWWLQJ
・
:KHQWKHFRPPXQLFDWLRQV\VWHPZDVFKDQJHG
)$667HVW&+
↔
)$667HVW&+HWF
)
・
:KHQDQHZPRGHOZDVFUHDWHGE\PRGHO
VHOHFWLRQ
Telemetry function (FASSTest /T-FHSS mode
only)
To use the telemetry function, set “Telemetry” to
“ACT”.
DL Interval (FASSTest/T-FHSS mode only)
When a telemetry function is enabled, the
UHFHLYLQJLQWHUYDOGRZQOLQNLQWHUYDORIVHQVRU
data can be changed.
If a DL interval is increased, the response of
the sensor data display becomes slower, but stick
response will improve.
ŏ5HWXUQWR
/LQNDJH
PHQX