FUTABA 16SZ - Page 84

85
＜ Linkagemenu ＞
Neutral point setting procedure
%HFRPHVWKHFRPSHQVDWLRQUHIHUHQFHSRLQW
*Adjusting the servo horn so that the neutral point position is
QHDUWKHSRVLWLRQPDNHVWKHPL[LQJDPRXQWVPDOO
+ROGWKHVHUYRKRUQDWDULJKWDQJOHWRWKH
OLQNDJHURGDQGWKHQWDSWKH>(QWHU@EXWWRQ
DQGUHDGWKHDFWXDOQHXWUDOSRLQW
*The neutral point is displayed on the screen.
 $IWHUUHDGLQJWKLVQHXWUDOSRLQWXVHRWKHU
FRPSHQVDWLRQIXQFWLRQVWRPDNHIXUWKHU
DGMXVWPHQWV
 7RH[LWWKHVHWWLQJWDSWKH>6ZDVK@EXWWRQ
Swash AFR setting procedure
 $GMXVWVRWKDWWKHVSHFLILHGRSHUDWLRQ
DPRXQWLVREWDLQHGE\DLOHURQHOHYDWRUDQG
SLWFKRSHUDWLRQ
7DSWKHEXWWRQRIWKH$)5UDWHWREH
DGMXVWHG9DOXHLQSXWEXWWRQVDSSHDURQWKH
VFUHHQ
8VHWKHYDOXHLQSXWEXWWRQVWRDGMXVWWKH$)5
UDWH
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
RUWKHGLUHFWLRQRIRSHUDWLRQFKDQJHV
 7RH[LWVHWWLQJWDSWKH>6ZDVK@EXWWRQ
Mixing rate setting procedure
+5LVGHVFULEHGDVDQH[DPSOH7KHPL[LQJ
DSSOLHGLQRWKHUVZDVKPRGHVLVGLIIHUHQWEXW
WKHVHWWLQJSURFHGXUHLVWKHVDPH
6HWWKHWKURWWOHVWLFNWRWKHVHWQHXWUDOSRLQW
$GMXVWWKHOHQJWKRIWKHOLQNDJHURGVRWKDW
WKHVZDVKSODWHLVKRUL]RQWDODWWKLVSRVLWLRQ
*A little adjustment using sub trim should be OK.
*Adjust so that pitch operation when the pitch
curve
LVVWUDLJKWLVPD[LPXP
$GMXVWWKH$,/!3,7DPRXQWVRWKHUHLVQR
LQWHUIHUHQFHLQWKHHOHYDWRURUSLWFKGLUHFWLRQ
ZKHQWKHDLOHURQVWLFNLVPRYHGWRWKHOHIW
DQGULJKW
*Adjust the left and right sides separately.
$GMXVWWKH(/(!$,/DQG(/(!3,7DPRXQWVVR
WKHUHLVQRWLQWHUIHUHQFHLQWKHDLOHURQRUSLWFK
GLUHFWLRQZKHQWKHHOHYDWRUVWLFNLVPRYHG
XSDQGGRZQ
*Adjust the up and down sides separately.
$GMXVWWKH3,7!$,/DQG3,7!(/(DPRXQWVVR
WKDWWKHVZDVKSODWHLVKRUL]RQWDOZKHQWKH
WKURWWOHVWLFNLVVHWWRPD[LPXPVORZDQGIXOO
KLJK
*Adjust the slow and high sides separately.
7RH[LWVHWWLQJWDSWKH>6ZDVK@EXWWRQ
Linkage correction setting procedure
6HWWKHOLQNDJHFRPSHQVDWLRQDIWHUVHWWLQJWKHPL[LQJ
rate.
*This function compensates for elevator interference
by aileron operation or aileron interference by
HOHYDWRURSHUDWLRQDW/RZSLWFKDQG+LSLWFKDW
FROOHFWLYHSLWFK+5HWFFRQWURO
6HWWKHWKURWWOHVWLFNWRWKHPD[LPXPVORZ
SRVLWLRQ0RYHWKHDLOHURQVWLFNWRWKHOHIWDQG
ULJKWDQGDGMXVWWKHDLOHURQFRPSHQVDWLRQ
DPRXQWVRWKDWLQWHUIHUHQFHLQWKHHOHYDWRU
RUSLWFKGLUHFWLRQDWWKDWWLPHLVPLQLPDO
*The left and right sides can be adjusted separately.
*If the interference increases when the
compensation
amount is increased, make the compensation
direction "-".
$GMXVWWKHHOHYDWRUFRPSHQVDWLRQDPRXQW
VRWKDWWKHLQWHUIHUHQFHLQWKHDLOHURQRUSLWFK
GLUHFWLRQZKHQWKHHOHYDWRUVWLFNLVPRYHG
XSDQGGRZQLVPLQLPDO
3HUIRUPDLOHURQDQGHOHYDWRUFRPSHQVDWLRQ
VLPLODUO\IRUWKHWKURWWOHVWLFNIXOOKLJKVLGH
7RH[LWVHWWLQJWDSWKH>6ZDVK@EXWWRQ
Speed compensation setting procedure
6HWWKHWKURWWOHVWLFNWRWKHQHXWUDOSRLQW
SRVLWLRQ0RYHWKHHOHYDWRUVWLFNTXLFNO\DQG
DGMXVWWKHVSHHGFRPSHQVDWLRQDPRXQWVR
WKDWWKHLQWHUIHUHQFHLQWKHSLWFKGLUHFWLRQLV
PLQLPDO
7RH[LWVHWWLQJWDSWKH>6ZDVK@EXWWRQ
 Notes:
 ,IWKHOLQNDJHLVWRRORQJRUVKRUWFRUUHFW
FRPSHQVDWLRQZLOOQRWEHDSSOLHG&RUUHFW
WKLVEHIRUHFRQWLQXLQJ7KHSLWFKDQJOH
FKDQJHVDIWHUDQ\DGMXVWPHQW5HVHWWKH
SLWFKDQJOHZKHQDFWXDOO\IO\LQJDIWHU
FRPSHQVDWLRQSURFHVVLQJ