GAME SandPRO 35D - User Manual

Questions and Answers

K
Kenneth RobinsonJul 31, 2025
What to do if my GAME SandPRO 35D pump does not run?
- L
  Larry WolfeJul 31, 2025
  If the pump of your GAME Water Filtration System doesn't run, there are several potential causes: * **Not plugged in:** Check the socket and power cord to ensure they are properly connected. * **GFCI/or main circuit breaker tripped:** Switch on the breaker. If it trips again immediately, it indicates a defect in the pump or controls. * **Faulty Pump Motor:** The pump/motor assembly may need replacement.
S
samanthamcdanielAug 4, 2025
Why is there sand in my pool with GAME Water Filtration Systems?
- B
  bradley76Aug 5, 2025
  If you notice sand in your pool when using GAME Water Filtration Systems, here are a few possible reasons: * **Newly replaced sand:** Undersized grains may still be present. Backwash several times until the backwash water is clear. * **Sand in central valve (from backwash):** Purge into the drainpipe for 30 seconds. * **Damaged filter bottom strainer:** The filter's bottom strainer may be damaged and needs replacement.
A
Abigail HernandezAug 9, 2025
How to fix a leaking filter in GAME Water Filtration Systems?
- L
  Leonard RobertsAug 9, 2025
  If your GAME Water Filtration System filter is leaking: * Check the seal and replace it if it's faulty. * Tighten the clamp, but be careful not to overtighten the hose clamps (35 in/lb max torque).
J
James DavisAug 14, 2025
Why is there air in my GAME Water Filtration Systems?
- A
  Angela LeeAug 14, 2025
  If you find air in your GAME Water Filtration System, it could be due to a low water level or because the system was recently opened for service. While the pump is running, loosen (but do not remove) the pressure gauge or pressure gauge plug to release the air. Then, retighten the gauge or plug.
A
Alexis ClarkAug 17, 2025
What to do if water flows into the drainpipe from GAME Water Filtration Systems?
- B
  Brenda WilliamsAug 17, 2025
  If water flows into the drainpipe from your GAME Water Filtration System, it may be caused by dirt around the seal of the 4-way valve. Remove the 4-way valve from the tank and clean the seal.
M
Michelle ContrerasAug 22, 2025
How to remove air in the pump of GAME SandPRO 35D?
- M
  mramosAug 22, 2025
  If there's air in the pump of your GAME Water Filtration System, it might be due to a poor seal on the intake side. Tighten the hose clamps and connection fittings to resolve this.
X
xcoleAug 27, 2025
How to fix low pressure in GAME Water Filtration Systems?
- K
  kochchristopherAug 27, 2025
  If the pressure is too low in your GAME Water Filtration System, the hair and lint strainer basket may be dirty. Clean the hair and lint strainer.

Summary

Safety Warnings

Technical Specifications

Getting Started

Power Source Requirements

Details electrical requirements and safety precautions for power connection.

Assembly Instructions

Connecting the Filter System

Valve Operations

Filter Valve Settings and Functions

Describes the function of each setting: Filtration, Rinse, Backwash, Winterize/Drain.

Changing Valve Positions

Provides instructions and safety warnings for changing valve positions.

Filter Operations

Start Up

Details steps for initial filter system operation after assembly and filling.

Cleaning the Sand

Backwash Process

Step-by-step guide for performing the backwash procedure.

Backwash Dos and Donts

Maintenance

Adding New Sand

Cleaning the Hair and Lint Filter

Steps to clean the debris/lint filter in the pump's strainer basket.

Winterizing the System

Troubleshooting

GAME SandPRO 35D Specifications

General

Type	Sand Filter System
Pool Type	Above Ground
Pump Power	0.35 HP
Flow Rate	35 GPM
Voltage	115V
Filter Media	Silica Sand
Tank Material	Polyethylene
Valve Type	Multiport Valve

Related product manuals

GAME SandPRO 50D

20 pages

GAME SandPRO 75D