EasyManua.ls Logo

GAS GAS MC 250F 2022 - User Manual

GAS GAS MC 250F 2022
143 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OWNER'S MANUAL 2022
MC 250F
EX 250F
Art. no. 3215053en

Table of Contents

Questions and Answers

  • M
    mwilliamsAug 9, 2025
    Why is my GAS GAS MC 250F 2022 Motorcycle using so much oil?
    • O
      omillerAug 10, 2025
      High oil consumption in your GAS GAS Motorcycle can be due to several reasons. It could be that the engine vent hose is bent, in which case you should ensure it is routed without bends or replace it. Another cause might be that the engine oil level is too high, so check the engine oil level. If the engine oil is too thin, change the engine oil and oil filter, and clean the oil screen. Lastly, worn piston or cylinder can cause this issue, requiring you to measure the piston/cylinder mounting clearance.
  • L
    Laura WilliamsonAug 20, 2025
    What to do if my GAS GAS MC 250F 2022 Motorcycle 12-V battery keeps discharging?
    • J
      Jennifer WadeAug 20, 2025
      If the 12-V battery in your GAS GAS Motorcycle is discharged, it could be due to a couple of reasons. One possibility is that the 12 V battery is not charging, in which case you should check the charging voltage and the stator winding of the alternator. Another reason could be an unwanted electrical power consumer; check the open-circuit current to resolve this.
  • P
    Patricia CollierAug 30, 2025
    What causes an error level condition in GAS GAS MC 250F 2022?
    • C
      christinemillerAug 31, 2025
      An error level condition on your GAS GAS Motorcycle can be triggered by various sensor or programming issues. These include the necessity for throttle valve position programming or faults within the crankshaft speed sensor circuit. Additionally, issues such as circuit faults or incorrect input signals (too high or too low) from sensors like the throttle valve position sensor A, induction manifold pressure sensor, coolant temperature sensor, intake air temperature sensor, or tilt sensor can cause this. Problems with battery voltage (too high) or the gear position sensor (circuit fault, high input signal, or malfunction) can also lead to an error level condition. Addressing these issues involves checking and correcting the specific circuit fault or signal problem identified.

Summary

Safety Advice

Tampering Warning

Safe Operation

Outlines essential practices for safe and responsible motorcycle operation.

Protective Clothing

Emphasizes the importance of wearing appropriate protective gear for rider safety.

Use Definition - Intended Use

Misuse

Safety Advice

Degrees of Risk and Symbols

Important Notes

Manufacturer Warranty, Implied Warranty

Service

Controls

Clutch Lever

Hand Brake Lever

Throttle Grip

Stop Button

Start Button

Overview of Indicator Lamps

Opening the Fuel Tank Filler Cap

Closing the Fuel Tank Filler Cap

Cold Start Button

Idle Speed Adjusting Screw

Shift Lever

Foot Brake Lever

Preparing for Use

Advice on Preparing for First Use

Offers crucial advice for initial operation and safety checks.

Running in the Engine

Provides guidelines for breaking in the engine to ensure longevity.

Starting Power of Lithium-Ion Batteries at Low Temperatures

Preparing the Vehicle for Difficult Operating Conditions

Preparing the Vehicle for Rides on Dry Sand

Preparing the Vehicle for Rides on Wet Sand

Preparing the Vehicle for Rides on Wet and Muddy Circuits

Preparing Vehicle for High Temperatures or Slow Riding

Preparing the Vehicle for Low Temperatures or Snow

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Lists pre-ride checks to ensure safe operation.

Starting the Vehicle

Explains the correct procedure for starting the motorcycle engine.

Starting Off

Shifting, Riding

Applying the Brakes

Explains how to use the brakes effectively and safely.

Stopping, Parking

Provides instructions for safely stopping and parking the motorcycle.

Transporting

Refueling

Details the safe and correct procedure for refueling the motorcycle.

Service Schedule

Required Work

Lists maintenance tasks to be performed based on operating hours or time.

Recommended Work

Lists optional but recommended maintenance tasks.

Tuning the Chassis

Checking the Basic Chassis Setting with the Riders Weight

Explains how to set up the chassis based on rider weight.

Air Suspension XACT

Details the WP XACT air suspension system used in the fork.

Compression Damping of the Shock Absorber

Explains high-speed and low-speed compression damping adjustments.

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Provides steps to adjust low-speed compression damping.

Adjusting the High-Speed Compression Damping of the Shock Absorber

Details how to adjust high-speed compression damping.

Adjusting the Rebound Damping of the Shock Absorber

Explains how to adjust rebound damping.

Measuring the Dimension of the Rear Wheel Unloaded

Checking the Static Sag of the Shock Absorber

Explains how to check static sag for suspension setup.

Checking the Riding Sag of the Shock Absorber

Details how to check riding sag for suspension tuning.

Adjusting the Spring Preload of the Shock Absorber

Provides steps for adjusting shock absorber spring preload.

Adjusting the Riding Sag

Guides on adjusting riding sag for optimal suspension performance.

Checking the Basic Setting of the Fork

Explains how to check the fork's basic setup.

Adjusting the Fork Air Pressure

Details how to adjust the air pressure in the fork legs.

Adjusting the Compression Damping of the Fork

Explains how to adjust fork compression damping.

Adjusting the Rebound Damping of the Fork

Guides on adjusting fork rebound damping.

Handlebar Position

Adjusting the Handlebar Position

Provides instructions for adjusting handlebar position for ergonomics.

Service Work on the Chassis

Raising the Motorcycle with a Lift Stand

Removing the Motorcycle from the Lift Stand

Bleeding the Fork Legs

Removing the Fork Legs

Installing the Fork Legs

Removing the Lower Triple Clamp

Installing the Lower Triple Clamp

Checking the Steering Head Bearing Play

Explains how to check for play in the steering head bearings.

Adjusting the Steering Head Bearing Play

Guides on adjusting steering head bearing play.

Removing the Shock Absorber

Installing the Shock Absorber

Removing the Air Filter

Cleaning the Air Filter and Air Filter Box

Installing the Air Filter

Removing the Main Silencer

Installing the Main Silencer

Changing the Glass Fiber Yarn Filling of the Main Silencer

Removing the Fuel Tank

Installing the Fuel Tank

Cleaning the Chain

Checking the Chain Tension

Explains how to check the drive chain tension.

Adjusting the Chain Tension

Guides on adjusting the drive chain tension.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Checking the Frame

Checking the Link Fork

Adjusting the Basic Position of the Clutch Lever

Checking;Correcting the Fluid Level of the Hydraulic Clutch

Explains how to check and correct the hydraulic clutch fluid level.

Changing the Hydraulic Clutch Fluid

Details the procedure for changing the hydraulic clutch fluid.

Brake System

Checking the Free Travel of the Hand Brake Lever

Explains how to check free travel of the front brake lever.

Adjusting the Basic Position of the Hand Brake Lever

Guides on adjusting the hand brake lever position.

Checking the Brake Discs

Checking the Front Brake Fluid Level

Guides on checking the front brake fluid level.

Adding Front Brake Fluid

Explains how to add front brake fluid.

Checking the Front Brake Linings

Details how to check front brake lining thickness and condition.

Changing the Brake Linings of the Front Brake

Guides on replacing front brake linings.

Checking the Free Travel of Foot Brake Lever

Explains how to check free travel of the rear brake lever.

Adjusting the Basic Position of the Foot Brake Lever

Guides on adjusting the foot brake lever position.

Checking the Rear Brake Fluid Level

Guides on checking the rear brake fluid level.

Checking the Brake Linings of the Rear Brake

Details how to check rear brake lining thickness and condition.

Changing the Rear Brake Linings

Guides on replacing rear brake linings.

Wheels, Tires

Removing the Front Wheel

Installing the Front Wheel

Removing the Rear Wheel

Installing the Rear Wheel

Checking the Tire Condition

Checking Tire Pressure

Checking the Spoke Tension

Electrical System

Removing the 12-V Battery

Installing the 12-V Battery

Charging the 12-V Battery

Details the procedure for charging the 12-V battery.

Changing Main Fuse

Diagnostics Connector

Cooling System

Checking the Antifreeze and Coolant Level

Explains how to check coolant and antifreeze levels.

Draining the Coolant

Refilling with Coolant

Changing the Coolant

Tuning the Engine

Checking the Play in the Throttle Cable

Explains how to check throttle cable play.

Adjusting the Play in the Throttle Cable

Guides on adjusting throttle cable play.

Adjusting the Characteristic Map of the Throttle Response

Details how to change throttle response characteristics.

Adjusting the Idle Speed

Guides on adjusting the engine idle speed.

Programming the Throttle Valve Position

Checking the Basic Position of the Shift Lever

Adjusting the Basic Position of the Shift Lever

Service Work on the Engine

Changing the Fuel Screen

Checking the Engine Oil Level

Explains how to check the engine oil level.

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen

Details the process for changing engine oil, filter, and cleaning the screen.

Adding Engine Oil

Guides on adding engine oil to the correct level.

Cleaning, Care

Cleaning the Motorcycle

Storage

Storage

Putting into Operation After Storage

Troubleshooting

Faults

Lists common faults, their possible causes, and recommended actions.

Blink Code

Blink Code for Malfunction Indicator Lamp

Explains diagnostic blink codes indicated by the malfunction lamp.

Technical Data

Engine

Lists engine specifications like displacement, bore, stroke, and valve clearance.

Engine Tightening Torques

Specifies torque values for various engine fasteners.

Capacities

Lists capacities for engine oil, coolant, and fuel.

Chassis

Provides chassis specifications including frame, fork, and suspension details.

Electrical System

Tires

Fork

Shock Absorber

Chassis Tightening Torques

Specifies torque values for chassis components.

Substances

Brake Fluid DOT 4; DOT 5.1

Coolant

Engine Oil (SAE 10 W;50)

Fork Oil (SAE 4) (48601166 S1)

Shock Absorber Fluid (SAE 2.5) (50180751 S1)

Super Unleaded (ROZ 95)

GAS GAS MC 250F 2022 Specifications

General IconGeneral
Engine TypeSingle-cylinder, 4-stroke
Bore x Stroke78 mm x 52.3 mm
Compression Ratio13.9:1
Fuel SystemElectronic Fuel Injection
Starting SystemElectric starter
Transmission6-speed
Front Brake260 mm disc
Rear Brake220 mm disc
Fuel Tank Capacity7.5 L
Ground Clearance370 mm
Displacement249.9 cm³
Throttle Body44 mm
Front SuspensionUSD 48 mm forks
Front Tire80/100-21

Related product manuals