GE 19234 User Manual

9.Testoperation.Ifthechimedoesnotwork,see
TROUBLESHOOTING.
Ifyoudonotwanttodrillholesinyourdoorframe,you
canusethesupplieddoublesidedtapeforinstallation.
1.Cleanallmountingsurfaceswitha50/50mixtureof
isopropylalcohol.
2.Removethebackingfromonesideofthedouble
sidedtapeandpresstheexposedsideagainstthe
backplateofthepushbutton.
3.Removetheotherbackingstripandpressthe
exposedsideagainstthedoorframewhereyouwant
thebuttoninstalled.
Operation
1.Plugthechimeintoa120VACoutletandslidethe
powerswitchtothe“On”positiontoturnonthe
chime.TheredLEDpowerindicatorwilllight.
2.Gentlypresstransmitterbuttontosoundchime.
Troubleshooting
Chimedoesn’twork:
1.Makesurepushbuttonswitchisdepressedandheld
foratleast1second.
2.Makesurehousecodeswitches1-4onchimeand
pushbuttonmatchexactly.
3.Verifybatteryorientationinpushbutton.
4.Tryfreshbatteries.
5.Makesurechimeisnotfartherthan150feetaway
frompushbutton.
6.Ensurepushbuttonisnotmountedonmetal,near
metalstuds,orneartheoor.
7.Tryanewlocationforthechime.
Functionalrangemaybeadverselyaffectedbyoneor
moreofthefollowingfactors:weather,radiofrequency
interference,lowtransmitterbatteryandobstructions
betweenthetransmitterandreceiver.
ThisdevicecomplieswithPart15oftheFCCrules.
Operationissubjecttothefollowingconditions:
1.Thisdevicemaynotcauseharmfulinterference,and
2.Thisdevicemustacceptinterferencereceived,
includinganyinterferencethatmaycauseundesired
operation.
For technical support contact Jasco Products
Company at 1-800-654-8483
or www.jascoproducts.com
GEModel19234
www.jascoproducts.com

Wireless Door Chime Kit
Installation Instructions AC Wireless Chime Kit
Required Tools: Small at blade screwdriver, drill,
1/16” drill bit, and phillips screwdriver.
Included Hardware:
(2)3x20mmscrews
(1)Doublesidedadhesivepad
Thewirelessdoorchimekithastwocomponents:

 BatteryOperated
Chime(Receiver) PushButton(Transmitter)
Plugsinto120Voutlet Batteryincluded
Setting The House Security Code
Eachchimecomponenthas3jumpersforsettingthe
housesecuritycode.Inmostcasesyouwillnotneed
tochangethefactorysettingsforthehousesecurity
code.Ifyourchimeactivatesintermittentlyordoesnot
workatall,youmaybeabletosolvetheproblemby
changingyoursecuritycode.
Thechimeandpushbuttonmustbesettothesame
housesecuritycodeforthecombinationtooperate
together.
1.Removepowerfromthechime.
2.Toremovethebatteriesfromthepushbutton,
openthepushbuttoncaseasshownbelow.
3.LocatetheHouseSecurityCodedoorandscrew
locatedonthebackoftheChime.Removethe
screwandtakeoffthedoor.
4.Locatethechimeandpushbuttonjumpersshown
above.
5.Tochangethehousecode,addorremovejumpers
asneeded.Itisrecommendedtochangeonlyone
jumperatatimeandthentestthesystemforproper
operation.Thejumpersonthechimeandpushbutton
mustmatchexactly.
Wireless push button battery
Toinstallorreplacethebatteryinthewirelesspush
button.
1.Removethebackcoverofthepushbutton.
2.InstalltheA23(12volt)batterywiththenegative
sideofthebattery(-)towardthespringandthe
positivesideofthebattery(+)towardthepositive
batteryholderasshownbelow.
3.Replacebackcoverasshownbelow.
PushButtonMountingInstructions
Note:Avoidmountingonmetalsurfaces,asitmay
resultinareducedrangeoftransmission.Donotmount
inanareawhereexposedtodirectrain.
a.Removingthebackcover
b.Replacingthebackcover
Mounting Push Button
1.Pushbuttonsaretypicallymountedatthesame
heightasthedoorknoborhandle(between36”and
44”abovetheoor).
2.Beforemounting,chooseamountinglocationthat
isnotfartherthan150feetfromthechimeunit
location.
Not further than 150 feet
3.Beforeplacingthepushbuttonwhereyouwouldlike
tomountit,placethechimeasclosetonalposition
aspossible.Testtheoperationbeforedrilling.Ifit
works,mountthepushbutton.Ifitdoesnotwork,
seeTROUBLESHOOTING.
4.Usebackcoverofpushbuttonasatemplatetomark
twoscrewholes.
5.Drilltwoholeswith1/16”sizedrillinmarked
locations.
6.Securebackcovertothemountingsurfacewithtwo
suppliedmountingscrews.
7.Installthesupplied12Vbatteryobservingproper
polarity.(seebatteryinstallationsection)
8.Pressfronthousingontobackcover.
MadeinChina/HechoenChina
 isatrademarkof
GeneralElectricCompany
andisusedunderlicenseto
JascoProductsCompanyLLC,
10E.MemorialRd.,
OklahomaCity,OK73114.
www.jascoproducts.com
Rev.04-10    
     
19234
Pushbutton
HouseCode
Jumpers
Pushbutton
HouseCode
Jumpers
PushbuttonJumpers
4
5
6
8
PowerIndicator
On/OffSwitch
19234-1.indd 1 4/14/10 3:58 PM

GE 19234 Specifications

General

Accessory Type	Light Bulb
Type	LED
Voltage	120V
Lumens	800
Color Temperature	2700K
Life Hours	15000
Dimmable	Yes
Energy Star Certified	Yes
Bulb Shape	A19
Base Type	Medium (E26)

Summary

Installation Instructions AC Wireless Chime Kit

Setting The House Security Code

Instructions for setting the house security code for the chime and pushbutton.

Wireless Push Button Battery

Instructions for installing or replacing the battery in the wireless push button.

Mounting Push Button

Push Button Mounting Instructions

Guidelines for mounting the push button, avoiding metal surfaces and rain exposure.

Mounting Location and Testing

Recommendations for mounting location and testing the push button before final installation.

Operation and Troubleshooting

Operation

Steps to plug in the chime, turn it on, and test the transmitter button.

Troubleshooting: Chime Doesn't Work

Common issues and solutions when the wireless door chime does not function.

Functional Range and FCC Compliance

Factors Affecting Functional Range

Factors that can adversely affect the wireless chime's functional range.

FCC Compliance Statement

Device compliance with FCC rules and operational conditions.

Technical Support and Product Information

Technical Support Contact

Contact information for technical support and Jasco Products Company.