EasyManua.ls Logo

GE AUH2436ZGDA - User Manual

GE AUH2436ZGDA
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
31-5000483 Rev. 2 08-20 GEA
Split Type Heat Pump
Installation
Instructions
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
The manufacture recommends installing
AHRI listed matched indoor and outdoor
system. Installing approved matched indoor
and outdoor system will provide optimum
efficiency and best overall system reliability.

Table of Contents

Questions and Answers

  • D
    David NelsonJul 25, 2025
    What to do if my GE Heat Pump is not cooling or heating properly?
    • D
      Dwayne FergusonJul 25, 2025
      If your GE Heat Pump isn't cooling or heating well, several factors could be the cause. First, check for any blockages obstructing airflow and remove them. Ensure the temperature setting is correct and the fan speed is appropriately high. Adjust the airflow direction as needed and make sure all doors and windows are closed. If the thermostat is exposed to direct sunlight, relocate it. Reduce the number of heat sources in the room and, finally, clean or replace the air filter if it's blocked or dirty.
  • A
    amy37Aug 5, 2025
    Why won't my GE Heat Pump turn on?
    • D
      Dustin McneilAug 5, 2025
      Your GE Heat Pump might not be turning on due to several reasons. If you recently turned it off and back on, the compressor might be on a 3-minute delay to prevent damage. Wait three minutes before trying again. Other potential issues include incorrect or loose wiring connections—inspect and secure these. Also, verify that the fuse or circuit breaker is on and that the thermostat is set to call for heating or cooling.
  • T
    Tanya StuartAug 15, 2025
    How to stop dust coming from my GE Heat Pump?
    • C
      Cody WoodAug 15, 2025
      If you notice dust coming from your GE Heat Pump, start by checking the air filter and cleaning it if necessary. If the dust issue persists or is heavy, it could indicate that your duct system requires professional cleaning. Contact a duct cleaning specialist for further inspection and service.

Summary

Safety Information

Installation Instructions

Required Tools for Installation

Lists necessary tools for proper installation.

Accessories

Details included accessories for outdoor unit installation.

Installation Location

Guidelines for selecting an appropriate installation site.

Saltwater Coastal Installation

Specific instructions for units near salt water.

Outdoor Unit Clearances

Specifies required space around the outdoor unit.

Mounting the Unit

Instructions for securely mounting the outdoor unit.

Cold Climate Installation Requirement

Special considerations for installing in cold climates.

Pipe Installation Notes

Key considerations for refrigerant line set installation.

Conventional Line Set Installation: Pipe Bending

Proper techniques for bending refrigerant pipes.

Conventional Line Set Installation: Pipe Cutting; Pipe Flaring

Procedures for cutting and flaring refrigerant pipes.

Conventional Line Set Installation: Pipe Connection

Steps for connecting refrigerant lines securely.

Installation of Drain Pipe

Guidance on correctly installing the drain pipe.

Electrical Connection

Procedures for making electrical connections to the unit.

Terminal Strip

Information on wiring connections at the terminal strip.

Wiring Diagram

Visual representation of electrical wiring for the system.

Capacity Adjustments Instructions for Connect Series

How to adjust unit capacity settings.

Final Check

Checklist for verifying proper installation before operation.

Troubleshooting Tips

Common issues and their solutions for the heat pump.

Error Codes

List and explanation of system error codes.

Notes

Limited Warranty

GE AUH2436ZGDA Specifications

General IconGeneral
ModelAUH2436ZGDA
TypeHeat Pump
SEER Rating16
Voltage (V)208/230
Phase1
Refrigerant TypeR-410A
Sound Level (dB)74
Cooling Capacity (BTU)24000
Heating Capacity (BTU)24000

Related product manuals