Why does my GE GDF630PSMSS Dishwasher control panel lights go off?
If the control panel lights go off while you're setting the controls, it means there was too much time between touching the selected pads. Each pad must be touched within 30 seconds of the others. To relight, touch any pad again or open the door and unlock (top control).
Why is there water won’t pump out of the tub of my GE Dishwasher?
If water won’t pump out of the tub, the drain is likely clogged. If you have an air gap, clean it as described in the Care and Cleaning section. If the dishwasher drains into a disposer, run disposer clear. Check to see if your kitchen sink is draining well. If not, you may need a plumber.
What to do if my GE GDF630PSMSS control panel responded to inputs but dishwasher never filled with water?
If the control panel responds but the dishwasher never fills with water, make sure the door is firmly closed. Also, check that the water valve (usually located under the sink) is turned on. The flood float may be stuck. Remove the Ultra-Fine Filter assembly and lightly tap the piece under the ultra fine filter assembly that looks like a dome. Replace the filter.
What to do if water is standing in the bottom of my GE GDF630PSMSS Dishwasher tub?
If water is standing in the bottom of the tub, it's likely that the air gap is clogged. Clean the air gap. See the Care and Cleaning section. Also, check if a high drain loop or air gap is not installed. Refer to the Installation Instructions for proper drain line installation.
Why are my GE GDF630PSMSS Dishwasher dishes not drying?
If your dishes aren't drying, several factors could be the cause. Ensure the inlet water temperature is at least 120°F. Select Heated Dry or Dry Boost. Use Wash Temp Boost. Select a higher cycle, such as Steam Sani or Heavy. Check the rinse agent dispenser and fill as required. On some models, leaving the door closed after the Clean light appears allows the fan to run an additional 90 minutes. Note: If you open the door, this fan extension will be cancelled. If using Light cycle which uses lower water temperature and thus limited dry performance, switch to a different cycle. Allow cycles to fully complete. See Long cycle times in this Troubleshooting Tips section.
Why is my GE Dishwasher beeping once every minute?
The dishwasher beeping once every minute is a reminder that the door has been left open during operation. Press Start and close the door.
What to do if my GE Dishwasher won’t run?
If your dishwasher isn't running, check a few things: ensure that the fuse isn't blown or the circuit breaker isn't tripped, and replace the fuse or reset the breaker, removing any other appliances from the circuit. Also, make sure the power to the dishwasher is turned on, especially if it's connected to a wall switch. Lastly, the control panel might be locked; unlock it as described in the Getting started section.
How to fix spots and filming on glasses and flatware in GE Dishwasher?
Ensure correct installation and maintenance procedures are followed for safety.
Follow basic safety precautions when operating the dishwasher.
Covers electrical requirements and water heater safety guidelines.
Warnings and procedures to prevent child entrapment and ensure proper disposal.
How to inspect and clean the Ultra-Fine and Fine filter assemblies.
Solutions for unclean dishes, spots, filming, and cloudiness.
General| Type | Built-In |
|---|---|
| Color | Stainless Steel |
| Number of Wash Cycles | 6 |
| Drying System | Heated Dry |
| Control Type | Electronic |
| Capacity | 16 Place Settings |
| Dimensions (H x W x D) | 34 in x 24 in x 24 in |
| Water Filtration System | Yes |
| Rack Material | Nylon |
| Energy Star Certified | Yes |
| Delay Start | Yes |
| Soil Sensor | Yes |
| Third Rack | No |
| Stainless Steel Interior | Yes |
| Upper Rack Features | Adjustable |
To Next Page
