GE GDF640 Series - User Manual

Questions and Answers

L
Lisa HarringtonSep 4, 2025
How to prevent spots and filming on glasses and flatware in GE GDF640?
- B
  Brent CarpenterSep 4, 2025
  If your GE Dishwasher is leaving spots and filming on glasses and flatware, it could be due to several reasons. Extremely hard water may be the cause; try using rinse agents like Finish® Jet-Dry® Rinse Aid, and consider a water softener if the problem persists. Ensure your inlet water temperature is at least 120°F (49°C). Avoid overloading or improperly loading the dishwasher; refer to the Loading section for guidance. Check that your powder detergent is fresh and consider using a highly rated detergent such as Finish® Quantum® Automatic Dishwashing Detergent. Also, make sure your rinse agent dispenser is full by refilling it with a product like Finish® Jet-Dry® Rinse Aid. Finally, ensure you are using the proper amount of a highly rated detergent.
A
Amy BlakeAug 25, 2025
Why is there water standing in the bottom of my GE GDF640?
- P
  patrickclaytonAug 26, 2025
  If water is standing in the bottom of the tub of your GE Dishwasher, the air gap might be clogged; clean the air gap, see the Care and Cleaning section. Also, check if a high drain loop or air gap is not installed; refer to the Installation Instructions for proper drain line installation.
Z
zadamsAug 26, 2025
What to do if my GE Dishwasher won’t run?
- J
  johnsonrobertAug 26, 2025
  If your GE Dishwasher won’t run, there are a few things to check. First, see if a fuse is blown or a circuit breaker is tripped; replace the fuse or reset the circuit breaker and remove any other appliances from the circuit. Also, in some installations, the power to the dishwasher is provided through a wall switch; make sure it is on. Finally, the control panel might be locked; unlock the control panel, see the Getting started section.
R
Rachel SimpsonSep 12, 2025
How to turn off beeping at the end of the cycle on my GE GDF640?
- T
  Thomas YoungSep 12, 2025
  To turn off the double beep indicator (or re-activate it if it was previously turned off), press the Heated Dry pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
S
Sara BrownSep 18, 2025
What noises are normal for a GE GDF640?
- S
  samuel72Sep 18, 2025
  Normal operating sounds for GE Dishwashers include beeping at the end of the cycle (on some models), the detergent cup opening, water entering the dishwasher, the motor stopping and starting, spray arms starting and stopping, and drain pump sounds. If dishes are rattling, make sure they are properly loaded. If silverware is rattling against the door, tall utensils may be placed in the upper rack.
J
jeffreysheltonSep 7, 2025
How to remove stains from the tub interior of my GE Dishwasher?
- T
  Tara WagnerSep 7, 2025
  If your GE Dishwasher tub interior is stained, it could be due to several factors. Tomato-based foods can cause reddish stains; using the Steam Sani cycle after adding the dish can help decrease staining. Tea or coffee stains can be removed by hand with a solution of 1/2 cup bleach and 3 cups warm water, but avoid using bleach on stainless steel inner doors and wait at least 20 minutes after a cycle before cleaning. An overall yellow or brown film can be caused by iron deposits in water, which requires a special filter in the water supply line. White film can be caused by hard water minerals; use Finish® Jet-Dry® Rinse Aid and run the dishwasher with citric acid or Finish® Dishwasher Cleaner.
M
Michelle AndersonAug 31, 2025
What to do if my GE GDF640 control panel responded to inputs but dishwasher never filled with water?
- J
  James FullerSep 1, 2025
  If the control panel responds but the dishwasher doesn't fill with water: * Ensure the door is firmly closed. * Check that the water valve (usually under the sink) is turned on. * The flood float may be stuck. Remove the Ultra-Fine filter and lightly tap the piece under it that looks like a dome. Replace the filter.
A
Angela MartinSep 23, 2025
What does it mean when my GE Dishwasher is beeping at the end of the cycle?
- C
  Catherine EllisSep 23, 2025
  To turn off the double beep indicator (or re-activate it if it was previously turned off), press the Heated Dry pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
S
Shane WilliamsSep 14, 2025
What to do if there are suds in the GE GDF640 Dishwasher tub?
- L
  Lindsey CampbellSep 14, 2025
  If you see suds in your GE Dishwasher tub, it's likely due to using the wrong detergent or spilling rinse agent. Only use automatic dishwasher detergents to prevent sudsing; Finish® Quantum® Automatic Dishwashing Detergent is approved for use in all GE Appliances dishwashers. To remove existing suds, open the dishwasher and let them dissipate. Always wipe up any rinse agent spills immediately.
C
csotoAug 28, 2025
Why does my GE Dishwasher beep once every minute?
- E
  Eric HernandezAug 28, 2025
  If your GE Dishwasher is beeping once every minute, it's a reminder that the door has been left open during operation. To stop the beeping, press Start and close the door.

GE GDF640 Series Specifications

General

Type	Built-In
Capacity	16 place settings
Rinse Aid Dispenser	Yes
Energy Star Certified	Yes
Soil Sensor	Yes
Drying System	Heated Dry
Control Type	Electronic
Number of Options	5
Wash Arms	3
Upper Rack Features	Adjustable
Interior Material	Stainless Steel
Third Rack	Yes
Delay Start	Yes
Dimensions	34 H x 24 W x 24 D (inches)
Width	24 inches