To Next PageTo Next PageWhat to do if GE Washer door unlocks or won't start?
If the door unlocks or the machine doesn’t operate when you press Start on your GE Washer, remember that front-load washers start up differently than top-load washers, and it takes 30 seconds to check the system. The door will lock and unlock. Simply open and close the door firmly, then press Start.
Why is my GE GFWN1600 Washer making loud or unusual noises?
If your GE washer is making loud or unusual noises, vibrating, or shaking, it could be due to several factors. The washer is designed to move slightly (about 1/4 inch) to reduce forces transmitted to the floor, which is normal. Ensure all rubber leveling legs are firmly touching the floor by pushing and pulling on the back right and left sides of the washer to check if it is level. An unbalanced load can also cause these issues; pause the unit, open the door, and manually redistribute the load. A clogged pump could also be the reason.
Why is there not enough water in my GE GFWN1600 Washer?
If there's not enough water in your GE washer, it is normal. Horizontal washers do not require the tub to fill with water like top-load washers.
Why is softener or bleach not dispensing properly in my GE GFWN1600?
Improper dispensing of softener or bleach in your GE washer may be caused by: * A clogged dispenser: Clean the dispenser drawer monthly to remove buildup of chemicals. * Overfilling: Make sure to use the correct amount of softener or bleach, not exceeding the max line. * Cap issues: Make sure the softener and bleach cap for the dispenser are seated correctly.
Why is my GE GFWN1600 not draining, spinning, or tumbling?
If your GE Washer isn't draining, spinning, or tumbling, it might be due to several reasons. First, the load might be unbalanced; try redistributing the clothes and running a 'Drain + Spin' or 'Rinse + Spin' cycle. If you're washing a small load with heavy and light items, increase the load size. Also, check if the pump is clogged. Ensure the drain hose isn't kinked or that the washer isn't sitting on it. Your household drain could also be clogged, so it’s worth checking your plumbing. Finally, make sure the drain hose isn't siphoning because it's pushed too far down the drain; ensure there's an air gap between the hose and the drain.
Why is the dispenser drawer not dispensing properly in my GE GFWN1600 Washer?
If the dispenser drawer is not dispensing properly in your GE washer, it may be because laundry detergent packets have been placed in the dispenser drawer. Laundry detergent packets should not be used in the dispenser. They should only be added directly to the wash tub following the manufacturer's directions.
Why is there a bad odor inside my GE GFWN1600 Washer?
A bad odor inside your GE washer may be due to: * The washer being unused for a long time, not using the recommended quality of HE detergent, or using too much detergent: Run a Tub Clean cycle. In case of a strong odor, you may need to run the Tub Clean cycle more than once.
Why is there a detergent leak in my GE Washer?
If there is a detergent leak in your GE washer: * The detergent insert may be incorrectly placed: Make sure the detergent insert is properly located and fully seated. Never put detergent above the max line. * It is normal operation to see detergent leak on the door gasket about 20 seconds after filling the dispenser.
Why is my GE GFWN1600 Washer leaking water?
If your GE washer is leaking water, several factors could be the cause. Check the door gasket to ensure it's properly seated and not torn. If water is present on the back left of the washer, it indicates an oversudsing condition, suggesting you should use less detergent. Inspect the fill and drain hoses to confirm they are tightly connected at both the washer and the faucets, and that the drain hose is correctly inserted and secured to the drain. A clogged household drain could also be the culprit. The dispenser might be clogged, especially if you're using powder soap; remove the drawer and clean both it and the inside of the dispenser box. Make sure that you are using only HE detergent in the correct amount. Finally, if it's a new installation, check the dispenser box for any cracks.
Why does water not enter my GE GFWN1600 or enters slowly?
If water does not enter your GE Washer or enters slowly, it could be due to several reasons. First, after pressing Start, the washer performs system checks, and water will flow 60 seconds after Start is pressed. Ensure both hot and cold water faucets are fully turned on. Check the water valve screens and inlet hose screen washers for blockages; turn off the water source and remove the hoses to clean the screens. Other potential causes include improper sorting, overloading the washer, or selecting the incorrect wash cycle.
General| Color | White |
|---|---|
| Control Type | Electronic |
| Sanitize Cycle | Yes |
| Washer Type | Front Load |
| Wash Cycles | Active Wear, Delicates, Normal, Quick Wash, Sanitize |
