To Next PageTo Next PageWhy does the control time on my GE GFWN1600 display wrong or changes?
If the control time on your GE Washer is wrong or changes, it's likely normal. During the spin cycle, the washer may need to rebalance the load to reduce vibrations. When this happens, the estimated time is increased, causing the time left to increase or jump.
Why is my GE GFWN1600 Washer leaking water?
If your GE washer is leaking water, several factors could be the cause. Check the door gasket to ensure it's properly seated and not torn. If water is present on the back left of the washer, it indicates an oversudsing condition, suggesting you should use less detergent. Inspect the fill and drain hoses to confirm they are tightly connected at both the washer and the faucets, and that the drain hose is correctly inserted and secured to the drain. A clogged household drain could also be the culprit. The dispenser might be clogged, especially if you're using powder soap; remove the drawer and clean both it and the inside of the dispenser box. Make sure that you are using only HE detergent in the correct amount. Finally, if it's a new installation, check the dispenser box for any cracks.
Why is my GE GFWN1600 Washer making loud or unusual noises?
If your GE washer is making loud or unusual noises, vibrating, or shaking, it could be due to several factors. The washer is designed to move slightly (about 1/4 inch) to reduce forces transmitted to the floor, which is normal. Ensure all rubber leveling legs are firmly touching the floor by pushing and pulling on the back right and left sides of the washer to check if it is level. An unbalanced load can also cause these issues; pause the unit, open the door, and manually redistribute the load. A clogged pump could also be the reason.
Why is there not enough water in my GE GFWN1600 Washer?
If there's not enough water in your GE washer, it is normal. Horizontal washers do not require the tub to fill with water like top-load washers.
Why is softener or bleach not dispensing properly in my GE GFWN1600?
Improper dispensing of softener or bleach in your GE washer may be caused by: * A clogged dispenser: Clean the dispenser drawer monthly to remove buildup of chemicals. * Overfilling: Make sure to use the correct amount of softener or bleach, not exceeding the max line. * Cap issues: Make sure the softener and bleach cap for the dispenser are seated correctly.
Why is my GE GFWN1600 not draining, spinning, or tumbling?
If your GE Washer isn't draining, spinning, or tumbling, it might be due to several reasons. First, the load might be unbalanced; try redistributing the clothes and running a 'Drain + Spin' or 'Rinse + Spin' cycle. If you're washing a small load with heavy and light items, increase the load size. Also, check if the pump is clogged. Ensure the drain hose isn't kinked or that the washer isn't sitting on it. Your household drain could also be clogged, so it’s worth checking your plumbing. Finally, make sure the drain hose isn't siphoning because it's pushed too far down the drain; ensure there's an air gap between the hose and the drain.
Why is water not entering my GE GFWN1600 Washer?
If water isn't entering your GE Washer or is entering slowly, several factors could be at play. After you press Start, the washer performs system checks, and water should flow within 60 seconds. Ensure both hot and cold water faucets are fully turned on. Check the water valve screens and inlet hose screen washers for blockages; turn off the water source, disconnect the hoses, clean the screens, and then reconnect the hoses.
Why is my GE Washer not dispensing softener or bleach correctly?
If your GE Washer is not dispensing softener or bleach properly, clean the dispenser drawer monthly to remove any buildup of chemicals. Make sure you are using the correct amount of softener or bleach, and ensure the softener and bleach caps for the dispenser are seated correctly.
Why is water not entering my GE Washer, or entering slowly?
If water isn't entering your GE Washer or is entering slowly, consider these possibilities: * The washer performs automatic system checks after the Start button is pressed. Water will flow 60 seconds after Start is pressed. * Make sure both the hot and cold water faucets are fully turned on. * The water valve screens may be clogged. Turn off the water source, remove the water connection hoses from the back of the washer, and clean the screens with a brush or toothpick. Then, reconnect the hoses and turn the water back on. * The inlet hose screen washers may be clogged. Turn off the water source, remove the inlet hoses from the wall faucets, and clean the screen washers in the end of the hoses with a brush or toothpick. Reconnect the hoses and turn the water back on.
Why is my GE GFWN1600 improperly dispensing softener or bleach?
If your GE Washer is not dispensing softener or bleach properly, it may be because: * The dispenser is clogged. Clean the dispenser drawer monthly to remove any buildup of chemicals. * The softener or bleach is filled above the max line. Make sure you are using the correct amount of softener or bleach.
General| Color | White |
|---|---|
| Control Type | Electronic |
| Sanitize Cycle | Yes |
| Washer Type | Front Load |
| Wash Cycles | Active Wear, Delicates, Normal, Quick Wash, Sanitize |
