To Next PageTo Next Page
Need help?Do you have a question about the GE GTDS820EDWS and is the answer not in the manual?
General| Dryer Capactity | 7.8 cubic feet |
|---|---|
| Number of Cycles | 13 |
| Stackable | no |
| Venting | yes |
| Temperature Control | yes |
| Control Type | electronic |
| Delay Start | yes |
| Cycle Signal | yes |
| Interior Light | yes |
| Drying Rack | no |
| Moisture Sensor Option | yes |
| Steam | yes |
| Current | 25 amperes |
Weight and Dimensions| Depth | 31.9 inches |
|---|---|
| Height | 44.5 inches |
| Width | 28 inches |
| Net Weight | 160 pounds |
General safety warnings and precautions for operating and servicing the dryer.
Explains the meaning of characters in GE dryer model numbers.
Instructions on locating the mini manual within the dryer's backsplash area.
Details GE's replacement and labor warranty for dryer parts over specific periods.
Wiring diagram for electric dryer AC voltage to board and motor.
Wiring diagram for gas dryer AC voltage to board.
Circuit diagram for long vent models, showing blower motor connection.
Circuit diagram for mist models, showing water valve connection.
Procedure to enter and navigate through the dryer's service mode for diagnostics.
Table detailing various diagnostic tests available in service mode.
List of fault codes and their corresponding issues for dryer diagnostics.
Cross-references dryer model numbers with descriptions and IDs.
Details required voltage, amperage, and grounding for dryer installation.
Provides resistance and voltage specifications for key dryer components.
Lists fuse ratings, drum motor, and blower motor resistance values.
Diagram showing the location and labels of connectors on the main power board.
Procedure to test sensor rods for continuity and voltage drop.
Procedure to check the LED light functionality and resistance.
Procedure to test inlet thermistor resistance at different temperatures.
Procedure to test outlet thermistor resistance at different temperatures.
Procedure to measure heater resistance using multimeter connections.
Procedure to measure AC voltage at the heater connections.
Steps to diagnose a dryer with a non-responsive control board.
Procedure to test water valve resistance and AC voltage.
Procedure to check gas valve voltage and related components.
Procedure to measure drum and blower motor winding resistances.
Guide on how to view and service the igniter and flame sensor.
Details on proper electrical hookup and grounding for dryer installation.
Recommended maximum vent lengths for normal and long vent dryer installations.
Specifications for installing dryers in alcoves or closets.
Requirements for installing dryers in mobile or manufactured homes.
Specific instructions for dryer installation in garages.
Procedure for adjusting leveling legs to ensure dryer stability.
Tools and initial steps before reversing the dryer door swing.
Detailed instructions for disassembling and reassembling the dryer door.
General description of the dryer's control panel layout and features.
Explanation of power, start/pause, status lights, and cycle selection.
Description of various sensor and timed drying cycles available on the dryer.
Details on adjusting time, dryness level, and temperature settings.
Explanation of Delay Dry, Extended Tumble, eDry, and eMonitor features.
Information on Drum Light, Signal volume, and Control Lock features.
Details on energy-saving modes and automatic drying technology.
Description of how the dryer communicates with compatible washers.
Overview page for various disassembly procedures.
Instructions to remove the backsplash trim by pushing on side tabs.
Steps to slide backsplash rearward and remove screws.
Removing backsplash screws to access the main control board.
Procedure to remove screws and disengage spring clips for the top cover.
How to disengage the rear hold-down bracket and lift the top cover.
Identifying and removing screws securing the front panel.
Removing LED light and door switch from the front panel.
Instructions on removing screws holding the front drum roller support.
Steps to remove the belt and access drum rollers for replacement.
Diagram showing major electric dryer components.
Diagram and table for electric dryer thermistor/thermostat positions and values.
Diagram showing major gas dryer components.
Diagram and table for gas dryer thermistor/thermostat positions and values.
Procedure to remove the rear bulkhead for access to internal components.
Instructions for removing the blower wheel using a socket.
Steps to disconnect wires and remove the electric heater assembly.
Visual overview of gas heater components.
Procedure to remove the gas valve assembly.
Steps to remove the main burner assembly.
Instructions for replacing the glow bar igniter element.
Procedure to disconnect wire terminals and remove the flame sensor.
Steps to turn off water and disconnect the valve.
Procedure for removing and reinstalling the water valve.
Troubleshooting steps for dryers that won't start or don't heat.
Solutions for dryer vibration, noise, and greasy spots.
Addressing problems with clothes taking too long to dry or being wrinkled.
Troubleshooting tips for clothes shrinkage, wet collars, and color variation.
Resolving issues like garments being wet or dryer shutting off early.
