Why GEAppliances GTW485ASJWS detergent packets not dissolving?
Laundry detergent packets should not be used in the dispensers. They should only be added directly to the wash basket following the manufacturer’s directions.
What to do if my GEAppliances GTW485ASJWS Washer water leaks?
If your GEAppliances washer is leaking, there are several potential causes to investigate. First, ensure you are using the correct type and amount of detergent; switch to a High Efficiency detergent and use less of it, especially if you have soft water or are washing a small or lightly soiled load. Check that the fill and drain hoses are tightly connected at the faucets and that the rubber washers are installed correctly. Also, verify that the end of the drain hose is properly inserted and secured to the drain facility. Inspect your household plumbing for clogs, and ensure the drain hose isn't rubbing against the wall. Finally, tighten the hoses at the faucets and check the condition of the fill hoses, replacing them every 5 years if needed.
What to do if GEAppliances GTW485ASJWS water won’t drain?
If the water won’t drain from your GEAppliances washer, check the drain hose first. Make sure it is straightened and not kinked, and ensure the washer isn't sitting on it. Also, verify that the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
Why GEAppliances Washer water temperature seems incorrect?
If the water temperature in your GEAppliances washer seems incorrect, several factors could be the cause. Modern detergents are designed to work well with cooler water, improving energy efficiency. Ensure that both hot and cold water faucets are fully turned on and that the hoses are connected to the correct faucets, marked “H” and “C”. Check for clogged water valve screens by turning off the water source, disconnecting the hoses, cleaning the screens, and reconnecting. Also, make sure your house water heater is set to deliver water at 120°F–140°F (48°C–60°C). Note that on some models, cold water may be added periodically even when hot is selected, as the washer optimizes for best results.
Why GEAppliances Washer has too many suds?
If you are experiencing too many suds in your GEAppliances washer, it could be due to several reasons. If you have soft water, try using less detergent. Also, make sure you are measuring your detergent carefully and using less if you have soft water, a smaller load, or a lightly soiled load. Finally, consider switching to a High Efficiency detergent.
Why GEAppliances GTW485ASJWS leaves lint or residue on clothes?
If you notice lint or residue on your clothes after washing in your GEAppliances washer, several factors could be contributing. If you air dry your clothes, they may retain more lint. Ensure you are separating lint producers from lint collectors when sorting your laundry. Avoid washing small loads for too long by using the Light Soil setting. If the detergent isn't dissolving properly, try using a liquid detergent and warmer water. Avoid overloading the washer, and ensure you are loading clothes loosely around the outside of the basket. Finally, check the fabric softener package for instructions and follow directions for using the dispenser, making sure you have selected the Deep Rinse option.
Why is there small amount of water remaining in dispenser of GEAppliances GTW485ASJWS Washer?
It is normal for a small amount of water to remain in the dispenser of your GEAppliances washer after the cycle.
What to do if my GEAppliances GTW485ASJWS Washer leaves colored spots?
If your GEAppliances washer is leaving colored spots on your clothes, consider these potential causes. Check the fabric softener package for instructions and follow directions for using the dispenser, making sure you have selected the Deep Rinse option. Sort whites and lightly colored items separately from dark colors to prevent dye transfer. Ensure you are following the detergent manufacturer’s directions for the correct amount. If you have hard water, use a water conditioner or install a water softener. Verify that your water heater is delivering water at 120°F–140°F (48°C–60°C). Avoid overloading the washer by loosely loading clothes no higher than the top row of holes in the washer basket, and load items around the outside of the basket for best results. Pretreat the stain and rewash u...
What does blinking spin light mean on GEAppliances GTW485ASJWS Washer?
If the spin light is blinking or on at the end of the cycle on your GEAppliances washer, it indicates that an out-of-balance condition has been detected. Allow the cycle to continue and finish. If the load is still wet at the end of the cycle, even out the load and run a Drain & Spin cycle.
How to prevent snags, holes, tears, rips or excessive wear in GEAppliances GTW485ASJWS Washer?
To prevent snags, holes, tears, rips, or excessive wear in your GEAppliances washer, fasten snaps, hooks, buttons, and zippers before washing. Remove loose items like pins, objects from pockets, and sharp buttons. Turn knits (which snag easily) inside out. Check bleach package instructions for proper amount. Never add undiluted bleach to wash or allow clothes to come in contact with undiluted bleach. Rinse items that may have chemicals on them before washing. Use Speed Wash cycle with Extra Rinse option.
General| Brand | GE |
|---|---|
| Model | GTW485ASJWS |
| Appliance Category | Washer |
| Washer Type | Top Load |
| Capacity | 4.5 cu. ft. |
| Color | White |
| Control Type | Knobs |
| Number of Wash Cycles | 12 |
| Water Level | Automatic |
| Agitator | Yes |
| Spin Speed | 700 RPM |
| Energy Star Certified | Yes |
| Wash Cycles | Delicates, Heavy Duty, Quick Wash, Jeans, Whites, Colors |
| Water Levels | Low, Medium, High |
| Agitator Type | Dual Action |
| Width | 27 in |
| Depth | 27 in |
| Height | 44 in |
To Next Page
