gefran R-ETH100 - User Manual

R-ETH100
BRIDGE ETHERNET 100 MODULE
cod. 80127C / Edit 04 - 08/2011 - ENG
INSTALLATION AND OPERATION MANUAL
2 • INSTALLATION AND CONNECTION
This section contains the instructions necessary for correct
installation of the GILOGIK II into the machine control panel
or the host system and for correct connection of the system
power supply, inputs, outputs and interfaces.
Before proceeding with installation read the following
warnings carefully!
Remember that lack of observation of these warnings
could lead to problems of electrical safety and electroma-
gnetic compatibility, as well as invalidating the warranty.
Qualified staff
the installation and use of the system and components are only reserved
at qualified staff.
Conform use
the system and relative components are usable exclusively to the use
previewed in the manual
In order to guarantee a correct and sure operation are indispensable that
the product comes transported, stored correctly, installed, and controlled
second the previewed modalities.
Suitable for use in pollution degree 2 environment.
Open type equipment.
Electrical power supply
• theGILOGIKIIisNOTequippedwithanOn/Offswitch:theusermust
provide a two-phase disconnecting switch that conforms to the required
safety standards (CE marking), to cut off the power supply upstream of
thesystem.Theswitchmustbelocatedinthevicinityofthesystemand
must be within easy reach of the operator.
One switch may control more than one systems.
• Tomakesurethatthesystemveryisconnectedtoearthsecondthe
detailed lists of the relative understood one it.
• ifthesystemisusedinapplicationswithriskofdamagetopersons,
machinery or materials, it is essential to connect it up to auxiliary security
equipment. It is advisable to make sure that alarm signals are also
triggered during normal operation.
 ThedispositifmustNOTbeinstalledinflammableorexplosive
environments; it may be connected to equipment operating in such
atmospheres only by means of appropriate and adequate types of
interface, conforming to the applicable safety standards
Notes Concerning Electrical Safety and Electromagnetic
Compatibility:
• CE MARKING: EMC Conformity (electromagnetic compatibility)
in accordance with EEC Directive 2004/108/CE.
 TheGILOGIKIIsystemismainlydesignedtooperatein
industrial environments, installed on the switchboards or control panels
of productive process machines or plants.
 Normofapplicableproduct:EN61131-2.
 TheDeclarationofconformityisavailableonGEFRANweb:www.gefran.
com
• UL listed standard:UL508fileE198546
• BT Conformity (low tension)
 inaccordancewithDirectiveLVD2006/95/CE.
 AdviceforCorrectInstallationforEMC
Module power supply
• Supplywithclass2device
• Thepowersupplytothemodulesontheswitchboardsmustalways
come directly from an isolation device with a fuse.
• Theelectronicinstrumentsandelectromechanicalpowerdevices
such as relays, contactors, solenoid valves, etc., must always be
powered by separate lines.
• Whenthepowersupplyisstronglydisturbedbythecommutationof
transistor or power units or motors, an isolation transformer should
be
used, earthing the screen.
• Itisessentialthattheplanthasagoodearthconnection:
 -thevoltagebetweenneutralandearthmustnotbe>1V
 -theOhmicresistancemustbe<6Ω;
• Intheproximityofhighfrequencygeneratorsorarcwelders,use
adequate filters.
• Thepowersupplylinesmustbeseparatefromtheinstrumentinput
and output ones.
GEFRAN S.p.A. declines all responsibility for any damage
to persons or property caused by tampering, neglect,
improper use or any use which does not conform to the
characteristics of the controller and to the indications
given in these Instructions for Use.
I1 • MAIN FEATURES
• CompletecontrolofR-BUS(x)backplane
• RefreshofallinstalledI/Osin100us(1node)
• GDNetinterface
• Powersupplyofbackplane
3
80127C_MHW_R-ETH100_08-2011_ENG

Summary

Main Features of R-ETH100

Installation and Connection Guide

Qualified Staff for Installation

Installation and use of the system and components are only reserved at qualified staff.

Conform Usage Guidelines

System and components usable exclusively for previewed use in the manual.

Electrical Power Supply Requirements

User must provide a two-phase disconnecting switch conforming to safety standards.

EMC and Safety Compliance

Details CE Marking for EMC Conformity and UL listed standard.

EMC Installation Advice

Advice for correct installation to ensure electromagnetic compatibility.

Module Power Supply Details

Supply with class 2 device, always from an isolation device with a fuse.

Technical Data Specifications

Power Supply Specifications

24 VDC ±25% 2A max., powers the entire GILOGIK II system with polarity inversion protection.

Ethernet Interface Details

Standard RJ45 connection, 16 position rotary switch for node identification.

System Diagnostics Indicators

Details POWER, RUN, FAIL LEDs indicating module status.

Mechanical and Environmental Data

Includes dimensions, weight, fixing, protection level, and ambient conditions.

Connection Procedures

Node Identification Rotary Switch

Rotary switch to select the node, with values 0 (no active) and 1..F (1..15).

Ethernet Connection (RJ45)

Standard RJ45 connection using category 6 cable according to TIA/EIA-568A.

Power Supply Connection

Details the 24Vdc supply connection using unipolar cable with 1-1.5mm cross section.

gefran R-ETH100 Specifications

General

Brand	gefran
Model	R-ETH100
Category	Network Router
Language	English