2 0D5418 1 STARTER MOTOR FORD V-10 ENGINE
3 052625 11 SCREW SHC M10-1.5 X 35 G12.9
(2) 4 047411 1 / 2 SCREW HHC M6-1.0 X 16 G8.8
5 0D5623 2 HEAT SHIELD EXHAUST
6 0D2608 10 SCREW HHC 5/16-18 X 1/2 SSTL
7 070006 30 WASHER LOCK M8 SSTL
8 070008 10 WASHER FLAT M8 SS
9 055934M 1 CLAMP VINYL .75 X .343 Z
10 0G0321 1 HOSE COOL 5/8" ID 250#WP (14”)
11 046526 23 WASHER LOCK M10
12 057823 1 CLAMP HOSE #10 .56 - 1.06 (2300 & 3000RPM UNITS ONLY)
13 057765 1 ADAPTER M14-1.50 X 3/8 NPT
14 046964 1 ELBOW 90D 1/4 NPT F-M BRASS
15 0D5417 REF. SCREW HHC M10-1.0 X 25 G10.9
16 049821 3 SCREW SHC M8-1.25 X 30 G12.9
17 022129 3 WASHER LOCK M8-5/16
18 070010 2 SCREW HHC M8-1.25 X 35 SS F-TH
(2) 19 0F2776A 1 / 2 BRACKET SIGNAL CONDITIONER
(2) 20 022097 1 / 2 WASHER LOCK M6-1/4
21 048191 2 DOWEL PIN M10 X 24
(2) 22 022473 1 / 2 WASHER FLAT 1/4 ZINC
(1) 23 029333A 1 TIE WRAP UL 7.4" X .19" BLK (NOT SHOWN)
24 0D9913 18 SCREW SHC M8-1.25 X 35 SS
25 055596 1 BARBED STR 3/8 NPT X 3/8
26 069860E 1 HOSE DRAIN ASSY 28"
27 0D4255 2 GASKET EXHAUST MANIFOLD
28 057772 1 WASHER NYLON .565
29 0D6686 1 ASSEMBLY 6.8L G-BOX FLYWHEEL
30 0D3803 1 FLYWHEEL HOUSING MACH 6.8L V10
31 0D3805 1 COVER FLYWHEEL MACH 6.8L V-10
32 021113 1 PLATE DAMPNER RETNR
33 077996 1 CAP HOSE (2300 & 3000RPM UNITS ONLY)
34 022131 7 WASHER FLAT 3/8-M10 ZINC
35 0C7649 1 CLAMP HOSE .38-.87
36 052647 9 SCREW SHC M10-1.5 X 25 G12.9
37 0D2244M 1 ASSY MAGPICKUP(3/8-24 MALE)
38 0D3808 2 EXH MANIFOLD MACH 6.8L V-10
39 0F5114 1 DECAL REFER TO OWNERS MANUAL
41 079121 2 SCREW SHC M10-1.50 X 100 G10.9
43 057823 2 CLAMP HOSE #10 .56-1.06
44 053660 1 BARBED STR 1/4 NPT X 5/8
45 087599 1 PLUG PLASTIC 3/8 NPT
(1) NOTE: I/N 23 IS FOR HOLDING SENSORS TO I/N 19.
(2) QTY. REQ. FOR NON-MQT / QTY REQ. FOR MQT EPA CERT. (NOT REQUIRED
FOR NEXUS CONTROL PANELS)
To Next Page
Loading...
Need help?
General
